Since complete at91rm9200 SoC device was droped (due to replacement with
common at91 code) this parameter can safely be removed.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

The big "ARM: remove broken boards" series deletes all boards using
obsolete arm920t/at91rm9200 arch code. Therefore we can safely remove
this code now.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

TPS62361 is the new power supply used in OMAP4460 that
supplies vdd_mpu.

VCORE1 from Phoenix supplies vdd_core and VCORE2 supplies
vdd_iva. VCORE3 is not used in OMAP4460.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

- Add mkimage support for OMAP boot image
- Add support for OMAP boot image(MLO) generation in the new
  SPL framework

Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

- Add MMC raw and FAT mode boot support for OMAP
- Provide a means by which parameters passed by ROM-code
  can be saved in u-boot.
- Save boot mode related information passed by OMAP4 ROM-code
  and use it to determine where to load the u-boot from
- Assumes that the image has a mkimage header. Gets the
  payload size and load address from this header. If the
  header is not detected assume u-boot.bin as payload

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

- Provide alternate implementations of board_init_f()
  board_init_r() for OMAP spl.
- Provide linker script
- Initialize global data
- Add serial console support
- Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move
  it to board config header from config.mk

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

- Allow SPL to have .bss disjoint from rest of the image
- Allow for .bss setup in CONFIG_SPL_BUILD case too.
- Take care of the special case where relocation offset = 0.
- Compile out exception handling code and install a simpler
  vector

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Identify SDRAM devices connected to EMIF automatically:
LPDDR2 devices have some Mode Registers that provide details
about the device such as the type, density, bus width
etc. EMIF has the capability to read these registers. If there
are no devices connected to a given chip-select reading mode
registers will return junk values. After reading as many such
registers as possible and matching with expected ranges of
values the driver can identify if there is a device connected
to the respective CS. If we identify that a device is connected
the values read give us complete details about the device.

This along with the base AC timings specified by JESD209-2
allows us to do a complete automatic initialization of
SDRAM that works on all boards.

Please note that the default AC timings specified by JESD209-2
will be safe for all devices but not necessarily optimal. However,
for the Elpida devices used on Panda and SDP the default timings
are both safe and optimal.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Calculate EMIF register values based on AC timing parameters
from the SDRAM datasheet and the DDR frequency rather than
using the hard-coded values.

For a new board the user doen't have to go through the tedious
process of calculating the register values. Instead, just
provide the AC timings from the device data sheet as input
and the driver will automatically calculate the register values.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Add support for the SDRAM controller (EMIF).

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Add support for:
1. DPLL locking
2. Initialization of clock domains and clock modules
3. Setting up the right voltage on voltage rails

This work draws upon previous work done for x-loader by:
	Santosh Shilimkar <santosh.shilimkar@ti.com>
	Rajendra Nayak <rnayak@ti.com>

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

- separate mux settings into essential and non essential parts
- essential part is board independent as of now(so move it
  to SoC directory). Will help in having single SPL for all
  boards.
- Non-essential part(the pins not essential for u-boot to function)
  need to be phased out eventually.
- Correct mux data by aligning to the latest settings in x-loader

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

The basic hardware init of OMAP4(s_init()) can happen in 4
different contexts:
 1. SPL running from SRAM
 2. U-Boot running from FLASH
 3. Non-XIP U-Boot loaded to SDRAM by SPL
 4. Non-XIP U-Boot loaded to SDRAM by ROM code using the
    Configuration Header feature

What level of hw initialization gets done depends on this
context. Add a utility function to find this context.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Some of the LPSC constants were incorrect, and some were missing. This
commit fixes the incorrect constants (which were not used anywhere in
the tree) and adds all constants for both DA830 and DA850, as per the
TI datasheets.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

There are two main sets of LPSC constants, depending on the processor
family.  The DA8xx constants were given in an enum whereas the non-DA8xx
constants were preprocessor defines. This commit switches the DA8xx
constants to defines for consistency.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

The function davinci_emac_mii_mode_sel() is defined in
board/davinci/common/misc.c for any DA8xx CPU which has
CONFIG_DRIVER_TI_EMAC enabled. However, the prototype was only being
declared in <include/asm/arch/davinci_misc.h> for the DA850 EVM board.
This patch declares it for all DA8xx CPUs where CONFIG_DRIVER_TI_EMAC
is enabled.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Add a generic GPIO driver for the DaVinci DA8xx processors. It is turned
on by defining CONFIG_DA8XX_GPIO and fulfills the generic GPIO interface
specified in <asm/gpio.h> . The driver has support for both manipulating
GPIO pins as well as automatically configuring the pin multiplexor
registers to set the pin function to GPIO.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

In preparation for a generic GPIO driver for the DA8xx processors,
rename <asm/arch/gpio_defs.h> to <asm/arch/gpio.h> and fix up all files
which include it.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

These functions are not required when CONFIG_CMD_NET
is not defined:
  - setup_net_chip()
  - reset_net_chip()
  - board_eth_init()

This patch wraps them in #ifdef CONFIG_CMD_NET...#endif

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

The GPIO pin used for resetting the external LAN chip has
changed for Rev.G board.

The patch uses generic gpio API instead of direct access
to corresponding registers.

Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

In current implementation, the function sets up the ethernet
chip and resets it. The steps to reset depend upon the board
revision.

The patch moves the reset actions to new function reset_net_chip().

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

The array of strings corresponding to cpu revision is
used only when CONFIG_DISPLAY_CPUINFO is selected - in
the function print_cpuinfo().

Enclose definition of this array in #ifdef...#endif for
the same.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

* 'master' of git://git.denx.de/u-boot-mmc:
  Revert "AT91:mmc:fix multiple read/write error"

Signed-off-by: Simon Guinot <sguinot@lacie.com>

Signed-off-by: Shaohui Xie <b21989@freescale.com>
Cc: Mike Frysinger <vapier@gentoo.org>

Add support of MX25L4005 and MX25L8005 according to the datasheet
http://www.mct.net/download/macronix/mx25l8005.pdf



This patch has been tested with MX25L4005 and MX25L8005

Signed-off-by: Macpaul Lin <macpaul@andestech.com>

* 'master' of git://git.denx.de/u-boot-ppc4xx:
  net/4xx: Install interrupt handler after driver registration

* 'master' of git://git.denx.de/u-boot-blackfin:
  Blackfin: jtag-console: fix timer usage
  Blackfin: switch to common display_options()
  Blackfin: serial: move early debug strings into .rodata section
  Blackfin: adi boards: also set stderr to nc with helper
  Blackfin: update anomaly lists to latest public info
  Blackfin: serial: convert to bfin_{read,write} helpers
  Blackfin: split out async setup
  Blackfin: adi boards: enable pretty flash progress output
  Blackfin: drop unused dma.h header from start code
  Blackfin: portmux: allow header to be included in assembly files
  Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: enable mmc_spi support
  Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: update network settings
  Blackfin: sync MMR read/write helpers with Linux
  Blackfin: gpio: optimize free path a little
  Blackfin: post: setup default CONFIG_SYS_POST_WORD_ADDR
  Blackfin: uart: fix printf warning
  Blackfin: add init.elf helper code
  Blackfin: dont reset SWRST on newer bf526 parts
  Blackfin: adi boards: enable multi serial support by default
  Blackfin: uart: add multiple serial support
  Blackfin: uart: move debug buffers into local bss

* 'master' of git://git.denx.de/u-boot-mips:
  README: update MIPS related informations
  MIPS: make cache operation mode configurable
  MIPS: rename INFINEON_EBU_BOOTCFG to CONFIG_SYS_XWAY_EBU_BOOTFG
  MIPS: INCA-IP: rename inca-swap-bytes host tool

Fix:

tqm834x.c:299: warning: passing argument 1 of 'get_ram_size' discards
qualifiers from pointer target type

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>

Fix compiler warning:

cmd_fpga.c:318: warning: passing argument 3 of 'fit_image_get_data'
from incompatible pointer type

Adding the needed 'const' here entails a whole bunch of additonal
changes all over the FPGA code.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Murray Jensen <Murray.Jensen@csiro.au>
Acked-by: Andre <Schwarz&lt;andre.schwarz@matrix-vision.de>

Clean up some duplicated prototype declarations.
Get rid of now useless AVR32 initcalls.h file.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Graeme Russ <graeme.russ@gmail.com>

Also remove bogus comment.

Signed-off-by: Zhong hongbo <bocui107@gmail.com>
Changed commit message
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>