Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

Add support for Wind River's SBC8641D reference board.

Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Jon Loeliger <jdl@freescale.com>

Add support for the following DaVinci boards:
- DV_EVM
- SCHMOOGIE
- SONATA

Changes:

- Split into separate board directories
- Removed changes to MTD_DEBUG (or whatever it's called)
- New CONFIG_CMD party line followed
- Some cosmetic fixes, cleanup etc.
- Patches against the latest U-Boot tree as of now.
- Fixed CONFIG_CMD_NET in net files.
- Fixed CONFIG_CMD_EEPROM for schmoogie.
- Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and
   DV_EVM. Can't check if it works on SONATA, don't have a board any more,
   but it at least compiles.

Here is an excerpt from session log on SCHMOOGIE...

U-Boot 1.2.0-g6c33c785-dirty (Aug  7 2007 - 13:07:17)

DRAM:  128 MB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
ARM Clock : 297MHz
DDR Clock : 162MHz
ETH PHY   : DP83848 @ 0x01
U-Boot > iprobe
Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F
U-Boot > ping 192.168.253.10
host 192.168.253.10 is alive
U-Boot >

Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Zach Sadecki <Zach.Sadecki@ripcode.com>
Acked-by: Stefan Roese <sr@denx.de>

This series of patches adds support for 2 boards from Netstal Maschinen.

The HCU4 has a PPC405Gpr and
the HCU5 has a PPC440EPX.

The HCU4 has a somehow complicated flash setup, as the booteprom is
only 8 bits and the CFI 16 bits wide, which makes it impossible to use a more
elegant solution.

The HCU5 has only a booteprom as the whole code will be downloaded from a
different board which has HD, CD-ROM, etc and where all code is stored.

This is my third try. I incorporated all suggestions made by Wolfgang and Stefan.
Thanks them a lot.

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>

Signed-off-by: John Otken <john@softadvances.com>

This patch adds initial support for the Liebherr lwmon5 board euqipped
with an AMCC 440EPx PowerPC.

Signed-off-by: Stefan Roese <sr@denx.de>

Enable hush shell, environment in flash rather in EEPROM,
more user-friendly default environment, etc.
The simple EEPROM environment can be selected easily in the board
config file.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by Dan Malek, <dan@embeddedalley.com>

Add Konstantin Kletschke for scb9328.
Signed-off-by: Peter Pearse <peter.pearse@arm.com>

Reset support
BSP autoconfig support

This patch adds support for the new AMCC Acadia eval board.

Please note that this Acadia/405EZ support is still in a beta stage.
Still lot's of cleanup needed but we need a preliminary release now.

Signed-off-by: Stefan Roese <sr@denx.de>

Add support for the MPC8349E-mITX-GP, a stripped-down version of the
MPC8349E-mITX.  Bonus features include support for low-boot (BMS bit in
HRCW is 0) for the ITX and a README for the ITX and the ITX-GP.

Signed-off-by: Timur Tabi <timur@freescale.com>

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

This patch adds support for the Prodrive P3M750 (PPC750 & MV64460)
and the P3M7448 (MPC7448 & MV64460) PMC modules. Both modules are
quite similar and share the same board directory "prodrive/p3mx"
and the same config file "p3mx.h".

Signed-off-by: Stefan Roese <sr@denx.de>

Dave for mpc8360emds, and me for mpc8349emds.

PREREQUISITE PATCHES:

* This patch can only be applied after the following patches have been applied:

  1) DNX#2006090742000024 "Add support for multiple I2C buses"
  2) DNX#2006090742000033 "Multi-bus I2C implementation of MPC834x"
  3) DNX#2006091242000041 "Additional MPC8349 support for multibus i2c"
  4) DNX#2006091242000078 "Add support for variable flash memory sizes on 83xx systems"
  5) DNX#2006091242000069 "Add support for Errata DDR6 on MPC 834x systems"

CHANGELOG:

* Add support for the Freescale MPC8349E-mITX reference design platform.
  The second TSEC (Vitesse 7385 switch) is not supported at this time.

Signed-off-by: Timur Tabi <timur@freescale.com>

Patch by Haavard Skinnemoen, 06 Sep 2006

This patch adds support for the ATSTK1000 with the ATSTK1002 CPU
daughterboard.

ATSTK1000 is a full-featured development board for AT32AP CPUs. It
has two ethernet ports, a high quality QVGA LCD panel, a loudspeaker,
and connectors for USART, PS/2, VGA, USB, MMC/SD cards and
CompactFlash cards. For more information, please see this page:

http://www.atmel.com/dyn/products/tools.asp?family_id=682



The ATSTK1002 is a daughterboard for the ATSTK1000 supporting the
AT32AP7000 chip.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Patch by Haavard Skinnemoen, 6 Sep 2006 16:23:02 +0200

This patch adds common infrastructure code for the Atmel AVR32
architecture. See doc/README.AVR32 for details.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

- Add support for PPC440EPx & PPC440GRx
- Add support for PPC440EP(x)/GR(x) NAND controller
  in cpu/ppc4xx directory
- Add NAND boot functionality for Sequoia board,
  please see doc/README.nand-boot-ppc440 for details
- This Sequoia NAND image doesn't support environment
  in NAND for now. This will be added in a short while.
Patch by Stefan Roese, 07 Sep 2006

Patch by Sangmoon Kim, 18 Aug 2005

Patch by Thomas Lange, Aug 11 2005

  Patch by Scott McNutt, 08 Jun 2006

Patch by Stefan Roese, 02 Jun 2006

- Add IXP4xx NPE ethernet MAC support
- Add support for Intel IXDPG425 board
- Add support for Prodrive PDNB3 board
- Add IRQ support
Patch by Stefan Roese, 23 May 2006

[This patch does not include cpu/ixp/npe/IxNpeMicrocode.c which still
 sufferes from licensing issues. Blame Intel.]

Patch from Scott McNutt, 11 Aug 2005

- Support for TQM8541/8555 boards added.
- Complete rework of TQM8540/8560 support.
- Common TQM85xx code now supports all current TQM85xx platforms
  (TQM8540/8541/8555/8560).
- DDR SDRAM size detection added.
- CAS latency default values can be overwritten by setting "serial#"
  to e.g. "ABC0001 casl=25" -> CAS latency 2.5 will be used.
  If problems are detected with this non default CAS latency,
  the defualt values will be used instead.
- FLASH size detection added.
- Moved FCC ethernet driver initialization behind TSEC driver init
  -> TSEC is first device.

Patch by Stefan Roese, 30 Nov 2005

Patch by John Otken, 23 Nov 2005

Added CONFIG_NET_MULTI for VOM405 board.
Added reset_phy() for VOM405 board.
Patch by Matthias Fuchs, 09 Nov 2005

sed the linker scripts, rather than pre-process them.
Patch by Peter Pearse, 07 Oct 2005

Use lowlevel_init() instead of platformsetup() [rename].
Patch by Peter Pearse, 06 Oct 2005

Patch by Rowel Atienza, 06 Apr 2005

Patch by Cliff Brake, 04 Feb 2005

Patch by Matthias Fuchs, 22 Sep 2005