- separate mux settings into essential and non essential parts
- essential part is board independent as of now(so move it
  to SoC directory). Will help in having single SPL for all
  boards.
- Non-essential part(the pins not essential for u-boot to function)
  need to be phased out eventually.
- Correct mux data by aligning to the latest settings in x-loader

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

The basic hardware init of OMAP4(s_init()) can happen in 4
different contexts:
 1. SPL running from SRAM
 2. U-Boot running from FLASH
 3. Non-XIP U-Boot loaded to SDRAM by SPL
 4. Non-XIP U-Boot loaded to SDRAM by ROM code using the
    Configuration Header feature

What level of hw initialization gets done depends on this
context. Add a utility function to find this context.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Some of the LPSC constants were incorrect, and some were missing. This
commit fixes the incorrect constants (which were not used anywhere in
the tree) and adds all constants for both DA830 and DA850, as per the
TI datasheets.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

There are two main sets of LPSC constants, depending on the processor
family.  The DA8xx constants were given in an enum whereas the non-DA8xx
constants were preprocessor defines. This commit switches the DA8xx
constants to defines for consistency.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

The function davinci_emac_mii_mode_sel() is defined in
board/davinci/common/misc.c for any DA8xx CPU which has
CONFIG_DRIVER_TI_EMAC enabled. However, the prototype was only being
declared in <include/asm/arch/davinci_misc.h> for the DA850 EVM board.
This patch declares it for all DA8xx CPUs where CONFIG_DRIVER_TI_EMAC
is enabled.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Add a generic GPIO driver for the DaVinci DA8xx processors. It is turned
on by defining CONFIG_DA8XX_GPIO and fulfills the generic GPIO interface
specified in <asm/gpio.h> . The driver has support for both manipulating
GPIO pins as well as automatically configuring the pin multiplexor
registers to set the pin function to GPIO.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

In preparation for a generic GPIO driver for the DA8xx processors,
rename <asm/arch/gpio_defs.h> to <asm/arch/gpio.h> and fix up all files
which include it.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

These functions are not required when CONFIG_CMD_NET
is not defined:
  - setup_net_chip()
  - reset_net_chip()
  - board_eth_init()

This patch wraps them in #ifdef CONFIG_CMD_NET...#endif

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

The GPIO pin used for resetting the external LAN chip has
changed for Rev.G board.

The patch uses generic gpio API instead of direct access
to corresponding registers.

Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

In current implementation, the function sets up the ethernet
chip and resets it. The steps to reset depend upon the board
revision.

The patch moves the reset actions to new function reset_net_chip().

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

The array of strings corresponding to cpu revision is
used only when CONFIG_DISPLAY_CPUINFO is selected - in
the function print_cpuinfo().

Enclose definition of this array in #ifdef...#endif for
the same.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

* 'master' of git://git.denx.de/u-boot-mmc:
  Revert "AT91:mmc:fix multiple read/write error"

Signed-off-by: Simon Guinot <sguinot@lacie.com>

Signed-off-by: Shaohui Xie <b21989@freescale.com>
Cc: Mike Frysinger <vapier@gentoo.org>

Add support of MX25L4005 and MX25L8005 according to the datasheet
http://www.mct.net/download/macronix/mx25l8005.pdf



This patch has been tested with MX25L4005 and MX25L8005

Signed-off-by: Macpaul Lin <macpaul@andestech.com>

* 'master' of git://git.denx.de/u-boot-ppc4xx:
  net/4xx: Install interrupt handler after driver registration

* 'master' of git://git.denx.de/u-boot-blackfin:
  Blackfin: jtag-console: fix timer usage
  Blackfin: switch to common display_options()
  Blackfin: serial: move early debug strings into .rodata section
  Blackfin: adi boards: also set stderr to nc with helper
  Blackfin: update anomaly lists to latest public info
  Blackfin: serial: convert to bfin_{read,write} helpers
  Blackfin: split out async setup
  Blackfin: adi boards: enable pretty flash progress output
  Blackfin: drop unused dma.h header from start code
  Blackfin: portmux: allow header to be included in assembly files
  Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: enable mmc_spi support
  Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: update network settings
  Blackfin: sync MMR read/write helpers with Linux
  Blackfin: gpio: optimize free path a little
  Blackfin: post: setup default CONFIG_SYS_POST_WORD_ADDR
  Blackfin: uart: fix printf warning
  Blackfin: add init.elf helper code
  Blackfin: dont reset SWRST on newer bf526 parts
  Blackfin: adi boards: enable multi serial support by default
  Blackfin: uart: add multiple serial support
  Blackfin: uart: move debug buffers into local bss

* 'master' of git://git.denx.de/u-boot-mips:
  README: update MIPS related informations
  MIPS: make cache operation mode configurable
  MIPS: rename INFINEON_EBU_BOOTCFG to CONFIG_SYS_XWAY_EBU_BOOTFG
  MIPS: INCA-IP: rename inca-swap-bytes host tool

Fix:

tqm834x.c:299: warning: passing argument 1 of 'get_ram_size' discards
qualifiers from pointer target type

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>

Fix compiler warning:

cmd_fpga.c:318: warning: passing argument 3 of 'fit_image_get_data'
from incompatible pointer type

Adding the needed 'const' here entails a whole bunch of additonal
changes all over the FPGA code.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Murray Jensen <Murray.Jensen@csiro.au>
Acked-by: Andre <Schwarz&lt;andre.schwarz@matrix-vision.de>

Clean up some duplicated prototype declarations.
Get rid of now useless AVR32 initcalls.h file.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Graeme Russ <graeme.russ@gmail.com>

Also remove bogus comment.

Signed-off-by: Zhong hongbo <bocui107@gmail.com>
Changed commit message
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>

Fix the following:

ERROR: do not initialise statics to 0 or NULL
ERROR: do not use assignment in if condition

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Run cfb_console.c through indent and manually fix some of he
deficiencies of the automatic line breaking.

Fix multiline comments, excessive line spacing and such.

No changes to code done.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Amend section 'Directory Hierarchy' for current MIPS directory.
Describe config options for MIPS.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>

Currently the cache operation mode is hard-coded to
CONF_CM_CACHABLE_NONCOHERENT. This is not appropiate for CPUs or SOCs
which operate at a different mode.

This patch makes the cache operation mode configurable via board config.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>

This define is a board-specific config option and should be
renamed to follow the U-Boot naming convention. Additionally,
add an explaining comment for this option.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>

The INCA-IP SoC belongs to the Lantiq XWAY SoC product portfolio.
For the upcoming support of other Lantiq SoC devices this tool should
not solely depend on the INCA-IP board.

Rename the tool to xway-swap-bytes and add an config option
to enable compilation optionally.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>

* 'master' of /home/wd/git/u-boot/custodians:
  powerpc/8xxx: Remove dependency on <usb.h>
  powerpc/85xx: enable USB2 gadget mode for corenet ds board
  powerpc/85xx: verify the device tree before booting Linux
  MPC8xxx: drop redundant boot messages
  powerpc/85xx: Fix build failure for P1023RDS
  powerpc/p2041rdb: Enable SATA support
  powerpc/85xx: Cleanup handling of PVR detection for e500/e500mc/e5500
  powerpc/85xx: Fix up clock_freq property in CAN node of dts
  85xx: enable FDT support for STX SSA board
  powerpc/85xx: provide 85xx flush_icache for cmd_cache
  powerpc/p2041rdb: Enable backside L2 cache support
  powerpc/85xx: Handle the lack of L2 cache on P2040/P2040E
  powerpc/85xx: Add support for P2041[e] XAUI in SERDES
  powerpc/85xx: Rename P2040 id & SERDES to P2041
  powerpc/85xx: Adding configuration for DCSRCR to enable 32M access
  powerpc/85xx: Fix setting of EPAPR_MAGIC value

This is needed to get rid of build warnings like

main.c:311: warning: passing argument 2 of 'setenv' discards qualifiers from pointer target type

which result from commit 09c2e90c "unify version_string".

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andreas Biemann <andreas.devel@googlemail.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

We used <usb.h> for USB_MAX_DEVICE.  However this requires we actual
build in support for USB into u-boot (which should not be required for
device tree fixup).

At this time no FSL SoC that utilizies this code (83xx/85xx) has more
than 2 USB controllers.  So we replace USB_MAX_DEVICE with a local
define FSL_MAX_NUM_USB_CTRLS.

If/when a device shows up with more than 2 controllers we can easily
bump this value or refactor into a proper define per SoC.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

to make USB2 worked in gadget mode, we need to set it's 'dr_mode' to
'peripheral' in hwconfig, but driver starts scan from 'usb1', it'll break
out if it cannot find 'usb1', so drop the 'else' clause to make driver scan
all the 'usbx'.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Introduce ft_verify_fdt(), a function that is called after the device tree
has been fixed up, that displays warning messages if there is a mismatch
between the physical addresses of some devices that U-Boot has configured
with what the device tree says the addresses are.

This is a particular problem when booting a 36-bit device tree from a
32-bit U-Boot (or vice versa), because the physical address of CCSR is
wrong in the device tree.  When the operating system boots, no messages are
displayed, so the user generally has no idea what's wrong.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Current code would print RAM size information like this:

	DRAM:  DDR: 256 MiB (DDR1, 64-bit, CL=2, ECC off)

Turn a number of printf()s into debug() to get rid of the redundant
"DDR: " string like this:

	DRAM:  256 MiB (DDR1, 64-bit, CL=2, ECC off)

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

When we added the fman fdt fixup we forgot to fixup the P1023RDS
platform.  So we would get:

fdt.c: In function 'fdt_fixup_fman_firmware':
fdt.c:465:15: error: 'CONFIG_SYS_FMAN_FW_LENGTH' undeclared (first use in this function)
fdt.c:465:15: note: each undeclared identifier is reported only once for each function it appears in

Add the needed #defines in P1023RDS.h to fix this.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>