ehci-hcd.c: In function 'ehci_submit_root':
ehci-hcd.c:719: warning: value computed is not used
ehci-hcd.c:748: warning: value computed is not used

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.

More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html



Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

The cm-bf561 module can easily hook up to the EXT-BF5xx-USB-ETH2 extender
board, so add a simple example of how to do that in the board config.

Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The latest blackstamp boards can only run the SPI flash at 15MHz before
they start to crap out, so lower the max speeds accordingly.  The new SPI
flash also has different sector requirements, so update the environment
sizes as well.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

A few debug-type commands used to dump the raw icache/dcache data.  Useful
when trying to track down cache-related bugs.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Current code only sets the PCI vendor id to 0x1014 and
leaved device id to 0x0000.

Ths patch ....
a) uses the correct PCI_VENDOR_ID_IBM macro for this
b) sets the default device ID as stated in the UM to 0x0156
   by using PCI_DEVICE_ID_IBM_405GP for this.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

This patch moves some basic PCI initialisation from the 4xx cpu_init_f()
to cpu/ppc4xx/4xx_pci.c.

The original cpu_init_f() function enabled the 405EP's internal arbiter
in all situations. Also the HCE bit in cpc0_pci is always set.
The first is not really wanted for PCI adapter designs and the latter
is a general bug for PCI adapter U-Boots. Because it enables
PCI configuration by the system CPU even when the PCI configuration has
not been setup by the 405EP. The one and only correct place is
in pci_405gp_init() (see "Set HCE bit" comment).

So for compatibility reasons the arbiter is still enabled in any case,
but from weak pci_pre_init() so that it can be replaced by board specific
code.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

This driver is tested on Sheevaplug platform

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>

It fixes the access to the 'ehci' struct elements for mpc83xx which
should have been taken care of in 4ef01010
Sorry about that.

Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>

This patch fixes the access to the 'ehci' struct elements which should
have been taken care off in 4ef01010
Sorry about that.

Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>

These functions are no longer defined, so remove their prototypes.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>

fix a stray CONFIG_MPC83XX that escaped commit
0f898604.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>

Check that an argument is passed to ubifsmount and that addresses and
sizes are actually numbers for ubifsload. Also improve the instructions
a bit.

Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Stefan Roese <sr@denx.de>

The VID header offset is sometimes needed to initialize the UBI
partition. This patch adds it (optionally) to the command line
for the ubi part command.

(Lines have been properly wrapped since last version)

Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

This patch makes pll_write on PPC405EP boards
global and callable from C code.

pll_write can be used to dynamically modify the PLB:PCI divider
as it is required for 33/66 MHz pci adapters based on the 405EP.

board_early_init_f() is a good place to do that (check M66EN signal
and call pll_write() when it is required).

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

This patch implements the is_pci_host() function in a similiar way
as it is used on 440 targets.

The former path with CONFIG_PCI_HOST == PCI_HOST_AUTO does not
build on 405EP targets because checking the PCI arbiter is different.
So putting the fixed code into a separate function makes the code
more readable.

Also using is_pci_host() on 405 brings 405 and 440 PCI code
a little bit closer.

In preparation for an upcoming 405EP based PMC module I made this
function weak so that it can be overwritten from board specific code.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>

This patch fixes a debug compilation error for PPC4xx platforms, all
other architectures are not affected by this change.  The 'handler'
pointer was undefined.  The fix is exercised and has effect only if
DEBUG is defined.

Signed-off-by: Alessio Centazzo <acpatin@yahoo.com>
Signed-off-by: Stefan Roese <sr@denx.de>

This patch fixes printf format string compilation warnings in several
debug statements. It also fixes the dump of DDR controller MQ registers
found on some 44x and 46x platforms. The current register dump code
uses incorrect DCRs to access these registers.

Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>

This patch fixes 2 problems with FDT EBC mappings on Canyonlands.
First, NAND EBC mapping was missing, making Linux NAND driver
unusable on this board. Second, NOR remapping code assumed that
NOR is always on CS0, however when booting from NAND NOR is on CS3.

Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>

The check of data became severe from newest gcc.
This patch checked in gcc-4.2 and 4.3 .

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

all sh boards use the same cpu linker script so move it to cpu/$(CPU)

that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk

tested on r2dplus

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

currently we need to sync the linker script enty and TEXT_BASE manualy
and the reloc_dst is based on it

instead provide it now from the ldflags

tested on r2dplus

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>