Signed-off-by: Wolfgang Denk <wd@denx.de>

As this seems unclear, document how the flow of setting up
the MAC address is correct.

Signed-off-by: Heiko Schocher <hs@denx.de>

Text changed slightly, adding input from Mike Frysinger.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Only fill the device enetaddr with the contents of the eeprom,
do not program it in MAC address registers

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Ben Warren <biggerbadderben@gmail.com>

The ramdisk sections in doc/uImage.FIT/multi.its lack
load address and entry point properties. Using examples
from this file will result in unbootable image, u-boot
will issue the following error messages:

Can't get ramdisk subimage load address!
Ramdisk image is corrupt or invalid

This patch adds missing properties to ramdisk sections.

Signed-off-by: Felix Radensky <felix@embedded-sol.com>

$ ./MAKEALL suen3
jffs2_1pass.c: In function 'get_fl_mem':
jffs2_1pass.c:399: warning: unused variable 'id'
jffs2_1pass.c: In function 'get_node_mem':
jffs2_1pass.c:423: warning: unused variable 'id'

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom <Tom.Rix@windriver.com>

After determining how much DDR is actually in the system, set DBAT0 and
IBAT0 accordingly.  This ensures that the CPU won't attempt to access
(via speculation) addresses outside of actual memory.

On 86xx systems, DBAT0 and IBAT0 (the BATs for DDR) are initialized to 2GB
and kept that way.  If the system has less than 2GB of memory (typical for
an MPC8610 HPCD), the CPU may attempt to access this memory during
speculation.  The zlib code is notorious for generating such memory reads,
and indeed on the MPC8610, uncompressing the Linux kernel causes a machine
check (without this patch).

Currently we are limited to power of two sized DDR since we only use a
single bat.  If a non-power of two size is used that is less than
CONFIG_MAX_MEM_MAPPED u-boot will crash.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Use the same code between primary and secondary cores to init the
L1 cache.  We were not enabling cache parity on the secondary cores.

Also, reworked the L1 cache init code to match the e500mc L2 init code
that first invalidates the cache and locks.  Than enables the cache and
makes sure its enabled before continuing.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This patch fixes a problem introduced with patch eb5eb2b0
[ppc4xx: Cleanup PPC4xx I2C infrastructure]. We need to assign the I2C
base address to the "i2c" pointer inside of the controller loop.
Otherwise controller 0 is initialized multiple times instead of
initializing each I2C controller sequentially.

Tested on Katmai.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>

Booting a "Multi-File Image" including a linux kernel, ramdisk and
fdt, generated with

mkimage -A ppc \
    -O linux \
    -T multi \
    -C gzip \
    -a 00000000 \
    -e 00000000 \
    -n "kernel-2.6+initrd+dtb" \
    -d "vmlinux.bin.gz:ramdisk_image.gz:board.dtb" \
    multi.bin

actually fails, because ramdisk start and end addresses
didn;t get initialized. This patch fixes this issue.

Tested on the KUP4K board.

Signed-off-by: Heiko Schocher <hs@denx.de>

Update CHANGELOG

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

The ml300 board has a number of issues, but nobody cares about this
long-orphaned board any more.  Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>

The restructuring of the mkimage command in commit 89a4d6b1 ("tools:
mkimage: split code into core, default and FIT image specific")
introduced a bug that caused mkimage to segfault when run without
"-n name" option.  Initialize the imagename entry to prevent that.

Signed-off-by: Wolfgang Denk <wd@denx.de>

With old configuration it could happen tout=0 if CONFIG_SYS_HZ<1000.

Signed-off-by: Renato Andreola <renato.andreola@imagos.it>
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Stefan Roese <sr@denx.de>

440EPx fixed bootstrap options A, B, D, and E sets PLL FWDVA to a value = 1.
This results in the PLLOUTB being greater than the CPU clock frequency
resulting unstable 440EPx operation resulting in various software hang
conditions.

This patch reprograms the FWDVA satisfying the requirement of setting FWDVB
to a value greater than 1 while using one of the four deafult bootstrap options.

Signed-off-by: Rupjyoti Sarmah <rsarmah@amcc.com>
Acked-by : Victor Gallardo <vgallardo@appliedmicro.com>
Signed-off-by: Stefan Roese <sr@denx.de>

The soft-i2c code for AT91 defines I2C_SOFT_DECLARATIONS
for direct access by dereferencing a pio pointer.
The OTC570 platform uses the AT91 gpio API so it does not
need the pio variable.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>

Support for 16bpp was supposed to be in the code but was not working.
This makes it work and has been tested in the nhk8815 board.

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

Update CHANGELOG

Signed-off-by: Wolfgang Denk <wd@denx.de>

ep93xx timer: Make get_ticks() return a value in CONFIG_SYS_HZ resolution,
as announced by get_tbclk()

Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>

ep93xx timer: Use 64-bit values in usecs_to_ticks() in order to avoid
overflows in intermediate values

Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>

Signed-off-by: Asen Dimov <dimov@ronetix.at>

The crc table was being built as little endian for big endian
targets.  This would cause fw_printenv to always fail with
"Warning: Bad CRC, using default environment" messages.

Signed-off-by: Jeff Angielski <jeff@theptrgroup.com>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>

Fix warnings while compiling with CONFIG_VIDEO enabled:

diu.c: In function 'video_hw_init':
diu.c:158: warning: 'return' with no value, in function returning non-void
diu.c:162: warning: format '%ld' expects type 'long int', but argument 6 has type 'int'
diu.c:162: warning: format '%ld' expects type 'long int', but argument 7 has type 'int'

Signed-off-by: Anatolij Gustschin <agust@denx.de>

If a board uses cfb_console driver and splash image
and also defines CONFIG_SILENT_CONSOLE, the user is
locked out even if "silent" is not set. It is not
possible to get any output, neither on vga console
device nor on serial console after redirecting the
output to the serial console, since the GD_FLG_SILENT
flag remains set.

Fix the problem by redirecting the output from frame
buffer to serial console if splashimage is used.
Only suppress the output if "silent" environment
variable was set and don't set the GD_FLG_SILENT
flag arbitrarily.

Signed-off-by: Anatolij Gustschin <agust@denx.de>

I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;'

Signed-off-by: Thomas Weber <swirl@gmx.li>
Add some more: neither Makefile nor config.mk need execute permissions.
Signed-off-by: Wolfgang Denk <wd@denx.de>

Some registers of the mxcmmc driver were accessed using
16 bit accessor functions, because only the LSB is
significant. This is not needed and generates
warnings.

Signed-off-by: Stefano Babic <sbabic@denx.de>

So far, TFTP negotiated a fixed retransmission timeout of 5 seconds.
In some cases (busy networks, slow TFTP servers) this caused very
slow transfers. A new environment variable "tftptimeout" allows to
set this timeout. Lowering this value may make downloads succeed
faster in networks with high packet loss rates or with unreliable
TFTP servers.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Signed-off-by: FUJITA Kazutoshi <fujita@soum.co.jp>
Signed-off-by:  <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>

This patch removes the \n after the help message for mmcinfo.
This resulted in an empty line being displayed after the mmcinfo line
when the help command was given.

Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>

Signed-off-by: Scott McNutt <smcnutt@psyent.com>

Signed-off-by: Scott McNutt <smcnutt@psyent.com>

The new zlib code wants asm/unaligned.h, so have the Blackfin version pull
in the asm-generic/unaligned.h.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This is based on the asm-arm/unaligned.h, but made generic so all arches
that cannot do unaligned accesses can utilize it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

If a splashscreen is used the console scrolling used the
scroll size as needed when a logo was displayed. This
patch sets the scroll size to the whole screen if
a splashscreen is shown.

Signed-off-by: Matthias Weisser <matthias.weisser@graf-syteco.de>