The features list:
- Boot from NOR Flash
- DDR2 266MHz hardcoded configuration
- Local bus NOR Flash R/W operation
- I2C, UART, MII and RTC
- eTSEC0/1 support
- PCI host

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Heiko Schocher <hs@denx.de>

The TK885D board uses a TQM885D module from TQ, this port adds an
own configuration file and adds a last_stage_init() method to
configure the two PHYs, depending on the phy_auto_nego environment
variable.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

This is MPC8360E based board with:
- 256MB fixed SDRAM;
- 8MB Intel Strata NOR flash;
- StMICRO 64MiB NAND flash;
- two 10/100/1000 ethernet ports connected via Broadcom
  BCM5481 PHYs;
- two 10/100 ethernet ports connected via National
  DP83848 PHYs;
- one PCI and one miniPCI slots;
- four serial ports (two NS16550-compatible, two UCCs);
- four USB ports working through MPC8360E "FHCI" USB controller;
- Fujitsu MB86277 graphics controller;
- Analog to Digital Converter/Touchscreen controller, AD7843
  connected to SPI.

Features not supported in this patch are:
- StMICRO 64MiB NAND flash (patch sent);
- MINT framebuffer initialization (patch is pending);
- Fetching production information from the EEPROM via I2C;
- FHCI USB;
- Two slow UCCs used as RS-485 UARTs.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Add support for Instituto Atlantico's ATUM8548 board

Signed-off-by: robert lazarski <robertlazarski@gmail.com>

Add support for Wind River's SBC8548 reference board.

Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Signed-off by: Andy Fleming <afleming@freescale.com>

Add the MAINTAINER and MAKEALL entries for mpc837xemds

Signed-off-by: Dave Liu <daveliu@freescale.com>

This patch brings the PMC440 board configuration file.
Finally it enables the PMC440 board support.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

This board never left prototyping state and it
became a millstone round my neck. So remove it.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

These patches add support for the PPC440EPx-based "Korat" board to
U-Boot.  They are based primarily on support for the Sequoia board.

Signed-off-by: Larry Johnson <lrj@acm.org>

ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU,
which is a derivative of AT32AP7000.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU,
which is a derivative of AT32AP7000.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

This patch adds NAND booting support for the AMCC 405EX(r) eval boards.
Again, only one image supports both targets.

Signed-off-by: Stefan Roese <sr@denx.de>

The Haleakala is nearly identical with the Kilauea eval board. The only
difference is that the 405EXr only supports one EMAC and one PCIe
interface. This patch adds support for the Haleakala board by using
the identical image for Kilauea and Haleakala. The distinction is done
by comparing the PVR.

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

Add MPC8360EMDS_ATM_config and MPC832XEMDS_ATM_config into
Makfile and MAKEALL

Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Mahesh Jade <mahesh.jade@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>

Changes to the TSEC driver affect almost all 83xx, 85xx, and 86xx boards.
Now we can do a MAKEALL test on all of them!

Signed-off-by: Andy Fleming <afleming@freescale.com>

Signed-off-by: Stefan Roese <sr@denx.de>

and reorder the existing 83xx maintainers alpha.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Stefan Roese <sr@denx.de>

..by placing board entries one per line, as suggested by jdl.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Add support for Wind River's SBC8641D reference board.

Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Jon Loeliger <jdl@freescale.com>

Add support for the following DaVinci boards:
- DV_EVM
- SCHMOOGIE
- SONATA

Changes:

- Split into separate board directories
- Removed changes to MTD_DEBUG (or whatever it's called)
- New CONFIG_CMD party line followed
- Some cosmetic fixes, cleanup etc.
- Patches against the latest U-Boot tree as of now.
- Fixed CONFIG_CMD_NET in net files.
- Fixed CONFIG_CMD_EEPROM for schmoogie.
- Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and
   DV_EVM. Can't check if it works on SONATA, don't have a board any more,
   but it at least compiles.

Here is an excerpt from session log on SCHMOOGIE...

U-Boot 1.2.0-g6c33c785-dirty (Aug  7 2007 - 13:07:17)

DRAM:  128 MB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
ARM Clock : 297MHz
DDR Clock : 162MHz
ETH PHY   : DP83848 @ 0x01
U-Boot > iprobe
Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F
U-Boot > ping 192.168.253.10
host 192.168.253.10 is alive
U-Boot >

Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Zach Sadecki <Zach.Sadecki@ripcode.com>
Acked-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

This series of patches adds support for 2 boards from Netstal Maschinen.

The HCU4 has a PPC405Gpr and
the HCU5 has a PPC440EPX.

The HCU4 has a somehow complicated flash setup, as the booteprom is
only 8 bits and the CFI 16 bits wide, which makes it impossible to use a more
elegant solution.

The HCU5 has only a booteprom as the whole code will be downloaded from a
different board which has HD, CD-ROM, etc and where all code is stored.

This is my third try. I incorporated all suggestions made by Wolfgang and Stefan.
Thanks them a lot.

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>

Add the ability for modules from the Schindler cm5200 family to use a
single U-Boot image:
- rename cm1_qp1 to cm5200
- add run-time module detection
- parametrize SDRAM configuration according to the module we are running on

Few minor, board-specific fixes included in this patch:
- better MAC address handling
- updated default environment ('update' command uses +{filesize} now)
- improved error messages in the auto-update code
- allow booting U-Boot from RAM (CFG_RAMBOOT)

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>