Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: Stefan Roese <sr@denx.de>

This patch allows booting from FLASH the ML507 board by Xilinx.
Previously, U-Boot needed to be loaded from JTAG or a Sytem ACE CF

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>

Support for the adsvix was originally provided by Applied Data
Systems (ADS), inc., now EuroTech, Inc.
The board never shipped aside from some sample boards.

Signed-off-by: Adrian Filipi <adrian.filipi@eurotech.com>

The Xilinx ML507 Board is a Virtex 5 prototyping board that includes,
	among others:
	-Virtex 5 FX FPGA (With a ppc440x5 in it)
	-256MB of SDRAM2
	-32MB of Flash
	-I2C Eeprom
	-System ACE chip
	-Serial ATA connectors
	-RS232 Level Conversors
	-Ethernet Transceiver

This patch gives support to a standard design produced by EDK for this
board: ppc440, uartlite, xilinx_int and flash

- Includes Changes propossed by Stefan Roese and Michal Simek

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Acked-by: Stefan Roese <sr@denx.de>

The MVBC_P is a MPC5200B based camera system with Intel Gigabit ethernet
controller (using e1000) and custom Altera Cyclone-II FPGA on PCI.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>

Add AMCC Redwood reference board that uses the latest
PPC 464 CPU processor combined with a rich mix of peripheral
controllers. The board will support PCIe, mutiple Gig ethernet
ports, advanced hardware RAID assistance and IEEE 1588.

Signed-off-by: Feng Kan <fkan@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

By Cleanup out-or-tree building for some boards (.depend)
(commit:c8a3b109)
because filse ware changed, some SH-boards have compile error.
I revised this problem.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

This patch adds support for the Lyrtech SFF-SDR board,
based on the TI DaVinci architecture (ARM926EJS).

Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Philip Balister <philip@balister.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>

This patch adds basic support for the TQM8548 module from TQ-Components
(http://www.tqc.de/

) including DDR2 SDRAM initialisation and support for
eTSEC 3 and 4

Furthermore Flash buffer write has been enabled to speed up output to
the Flash by approx. a factor of 10.

Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>

Add MPC8343 based board mvBlueLYNX-M7.
It's a single board stereo camera system.
Please read doc/README.mvblm7 for details.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

SH7763RDP has SCIF, NOR Flash, Ethernet, USB host, LCDC and MMC.
In this patch, support SCIF, NOR Flash, and Ethernet.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

This is a replacement for ATSTK1002 with 64MB SDRAM and NAND flash on
board. It's currently in production and will be available soon.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>

...and add to MAKEALL script

Signed-off-by: Wolfgang Denk <wd@denx.de>

This patch adds support for the AT91SAM9RL chip and the AT91SAM9RLEK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This patch adds support for the AT91SAM9261 chip and the AT91SAM9261EK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by
Freescale.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

This patch is based on the port by Mihai Georgian (see linkstation.c for
Copyright information) and implements support for LinkStation / KuroBox HD
and HG PPC models from Buffalo Technology, whereby HD is deactivated at
the moment, pending network driver fixing.

Notice to users: this is pretty much a barebone port. Support for network
on HG models is already in the U-Boot mainline, but you might also want
patches to switch fan / phy modes depending on the negotiated ethernet
parameters. This patch also doesn't support console switching, booting EM
mode, Buffalo specific ext2 magic number. So, if you want to use any of
those, you need additional patches. Otherwise this patche provides a fully
functional u-boot with a network console on your system.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

This patch adds support for the Phytec Phycore-i.MX31 board

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

This patch adds support for the mx31 litekit board

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

Reverting became necessary after it turned out that the patches in
the u-boot-arm repo were modified, and in some cases corrupted.

This reverts the following commits:

	066bebd6
	7a837b73
	c88ae205
	a147e56f
	d6674e0e
	8c8463cc
	c98b47ad
	8bf69d81
	8c16cb0d
	a574a738
	1377b558
	1704dc20

Signed-off-by: Wolfgang Denk <wd@denx.de>

SPARC/LEON2: added support for Gaisler simulator GRSIM/TSIM for SPARC/LEON2 targets. See www.gaisler.com for information.

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>

SPARC/LEON3: added support for GR-CPCI-AX2000 FPGA AX board. The FPGA is exchangeable but a standard LEON3 design is assumed. See www.gaisler.com for information.

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>

SPARC/LEON3: added support for Altera NIOS Development kit (STRATIX II Edition) with GRLIB template design. See www.gaisler.com for information.

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>

SPARC/LEON3: added support for Gaisler GRSIM/TSIM2 SPARC/LEON3 simulatorn. See www.gaisler.com for information.

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>

SPARC/LEON3: added support for GR-XC3S-1500 board with GRLIB template design. See www.gaisler.com for board information.

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>

Support for booting from internal DataFlash, external DataFlash card
or NAND flash is available.

Signed-off-by: Stelian Pop <stelian@popies.net>

This board never went into production

Signed-off-by: Zachary P. Landau <zachary.landau@labxtechnologies.com>
Acked-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>

Signed-off-by: Matthew Fettke <mfettke@videon-central.com>
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>

Add some missing ARM boards to MAKEALL.  These build correctly,
unlike several of the boards already listed.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>