Add P3060 SoC specific information:cores setup, LIODN setup, etc

The P3060 SoC combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add support for Job Queue/Ring LIODN for the RAID Engine on P5020.  Each
Job Queue/Ring combo needs one id assigned for a total of 4 (2 JQs/2
Rings per JQ).  This just handles RAID Engine in non-DPAA mode.

Signed-off-by: Santosh Shukla <santosh.shukla@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document.
Any local bus transaction may fail during LBIU resynchronization
process when the clock divider [CLKDIV] is changing. Ensure there
is no transaction on the local bus for at least 100 microseconds
after changing clock divider LCRR[CLKDIV].

Refer to the erratum LBIU3 of mpc8548.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some
early version silicons. The default settings of the DDR IO receiver
biasing may not work at cold temperature. When a failure occurs,
a DDR input latches an incorrect value. The workaround will set the
receiver to an acceptable bias point.

Signed-off-by: Gong Chen
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Pre u-boot Flow:
1. User loads the u-boot image in flash
2. PBL/Configuration word is used to create LAW for Flash at 0xc0000000
   (Please note that ISBC expects all these addresses, images to be
    validated, entry point etc within 0 - 3.5G range)
3. ISBC validates the u-boot image, and passes control to u-boot
   at 0xcffffffc.

Changes in u-boot:
1. Temporarily map CONFIG_SYS_MONITOR_BASE to the 1M
   CONFIG_SYS_PBI_FLASH_WINDOW in AS=1.
   (The CONFIG_SYS_PBI_FLASH_WINDOW is the address map for the flash
    created by PBL/configuration word within 0 - 3.5G memory range. The
    u-boot image at this address has been validated by ISBC code)
2. Remove TLB entries for 0 - 3.5G created by ISBC code
3. Remove the LAW entry for the CONFIG_SYS_PBI_FLASH_WINDOW created by
   PBL/configuration word after switch to AS = 1

Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Kuldip Giroh <kuldip.giroh@freescale.com>
Acked-by: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Unified DDR driver is maintained for better performance, robustness and bug
fixes. Upgrading to use unified DDR driver for MPC83xx takes advantage of
overall improvement. It requires changes for board files to customize
platform-dependent parameters.

To utilize the unified DDR driver, a board needs to define CONFIG_FSL_DDRx
in the header file. No more boards will be accepted without such definition.

Note: the workaround for erratum DDR6 for the very old MPC834x Rev 1.0/1.1
and MPC8360 Rev 1.1/1.2 parts is not migrated to unified driver.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

DDR2 has different ODT table and values. Adding table according to Samsung
application note.

Fix additive latency calculation to avoid interger underflow.

Also converted typedef dynamic_odt_t to struct dynamic_odt.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Reduce the calculation error to 1ps.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The two slots on the same controller have different addresses.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Check second DIMM slot in case the first one is empty.
Honor DQS enable option for SDRAM mode register.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

DDR RCW varies at different speeds. It is common for all platform. Move it
out from corenet_ds.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Extend CAS write Latency (CWL) table to comply with DDR3 spec

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The MPC8536 seems to use only 3 bits for the major revision field in the
SVR rather than the 4 bits used by all other processors.  The most
significant bit is used as a mfg code on MPC8536.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The P1023 has two 1G ethernet controllers the first can run in
SGMII, RGMII, or RMII.  The second can only do SGMII & RGMII.

We need to setup a for SoC & board registers based on our various
configuration for ethernet to function properly on the board.

Removed CONFIG_SYS_FMAN_FW as its not used anywhere.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block.  Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman).  However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.

Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely.  This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.

Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.

We add support for the following SoCs:
 * P1023 - 1 Fman, 2x1g
 * P4080 - 2 Fman, each Fman has 4x1g and 1x10g
 * P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Some SOCs have discontiguously-numbered cores, and so we can't determine the
valid core numbers via the FRR register any more.  We define
CPU_TYPE_ENTRY_MASK to specify a discontiguous core mask, and helper functions
to process the mask and enumerate over the set of valid cores.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The old fdt_create_phandle didn't actually create a phandle it just
set one.  We'll introduce a new helper that actually does creation.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>

Add ifdef protection around fman specific code related to device tree
clock setup.  If we dont have CONFIG_SYS_DPAA_FMAN defined we shouldn't
be executing this code.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Issue: Address masking doesn't work properly.
When sum of the base address, defined by BA, and memory bank size,
defined by AM, exceeds 4GB (0xffff_ffff) then AMASKn[AM] doesn't mask
CSPRn[BA] bits.

Impact:
This will impact booting when we are reprogramming CSPR0(BA) and
AMASK0(AMASK) while executing from NOR Flash.

Workaround:
Re-programming of CSPR(BA) and AMASK is done while not executing from NOR
Flash. The code which programs the BA and AMASK is executed from L2-SRAM.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Issue:
Peripheral connected to IFC_CS3 may hamper booting from IFC.

Impact:
Boot from IFC may not be successful if IFC_CS3 is used.

Workaround:
If IFC_CS3 is used, gate IFC_CS3 while booting from NAND or NOR.
Also Software should select IFC_CS3 using PMUXCR[26:27] = 0x01.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Issue:
The NOR-FCM does not support access to unaligned addresses for 16 bit port size

Impact:
When 16 bit port size is used, accesses not aligned to 16 bit address boundary
will result in incorrect data

Workaround:
The workaround is to switch to GPCM mode for NOR Flash access.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

For an IFC Erratum (A-003399) we will need to access IFC registers in
cpu_init_early_f() so expand the TLB covering CCSR to 1M.

Since we need a TLB to cover 1M we move to using TLB1 array for all the
early mappings so we can cover various sizes beyond 4k.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add NAND support (including spl) on IFC, such as is found on the p1010.

Note that using hardware ECC on IFC with small-page NAND (which is what
comes on the p1010rdb reference board) means there will be insufficient
OOB space for JFFS2, since IFC does not support 1-bit ECC.  UBI should
work, as it does not use OOB for anything but ECC.

When hardware ECC is not enabled in CSOR, software ECC is now used.

Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
[scottwood@freescale.com: ECC rework and misc fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>

Before main memory (DDR) is initialized, the on-chip L1 cache is used as a
memory area for the stack and the global data (gd_t) structure.  This is
called the initial RAM area, or initram.  The L1 cache is locked and the TLBs
point to a non-existent address (so that there's no chance it will overlap
main memory or any device).  The L1 cache is also configured not to write
out to memory or the L2 cache, so everything stays in the L1 cache.

One of the things we might do while running out of initram is relocate CCSR.
On reset, CCSR is typically located at some high 32-bit address, like
0xfe000000, and this may not be the best place for CCSR.  For example, on
36-bit systems, CCSR is relocated to 0xffe000000, near the top of 36-bit
memory space.

On some future Freescale SOCs, the L1 cache will be forced to write to the
backing store, so we can no longer have the TLBs point to non-existent address.
Instead, we will point the TLBs to an unused area in CCSR.  In order for this
technique to work, CCSR needs to be relocated before the initram memory is
enabled.

Unlike the original CCSR relocation code in cpu_init_early_f(), the TLBs
we create now for relocating CCSR are deleted after the relocation is finished.
cpu_init_early_f() will still need to create a TLB for CCSR (at the new
location) for normal U-Boot purposes.  This is done to keep the impact to
existing U-Boot code minimal and to better isolate the CCSR relocation code.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.

CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file.  Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.

CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.

Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot).  All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.

README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add UTMI and ULPI PHY support for USB controller on qoriq series of
processors with internal UTMI PHY implemented, for example P1010/P1014
 - Use both getenv() and hwconfig to get USB phy type till getenv()
   is depricated
 - Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc
   has internal UTMI phy

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Flush the dcache before removing the TLB with caches enabled.
Otherwise this might lead to problems later on, e.g. while booting
Linux (as seen on ICON-440SPe).

Signed-off-by: Stefan Roese <sr@denx.de>

Change bd_t->bi_phy* arrays from 1 to 2 for PPC405EX since
405EX has 2 ethernet interfaces.

Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net>
Signed-off-by: Stefan Roese <sr@denx.de>

Result of running the following command to address Wolfgang's
comment about camel case:

for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done

Discussion:
http://patchwork.ozlabs.org/patch/84988/



Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Tuning some IO settings for better performance and power.
And consolidate all such IO settings at one place.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

SDRAM init was not working on ES1.0 due to a programming
error. A pointer that was passed by value to a function
was set in function emif_get_device_details(), but the effect
wouldn't be seen in the calling function. The issue came
out while testing for ES1.0 because ES1.0 doesn't have any
SDRAM chips connected to CS1

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

This patch contains the generic changes required after
change to generic API in the previous patch.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Convert all OMAP specific functions to use the common API
definitions in include/asm/gpio.h. In the process, made
few additional changes:
 - Use -EINVAL consistently. -1 was used in many places.
 - Removed one-liner static functions that were used only
   once. Replaced the content as necessary.
 - Combines implementation of functions omap_get_gpio_dataout()
   and omap_get_gpio_datain(). To do so, new static function
   _get_gpio_direction() was added.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

OMAP3: Add 37xx ESx revision numbers.

Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Howard D. Gray <howard.gray@matrix-vision.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Read directly from OMAP_GPIO_DATAOUT to get the output state of the GPIO pin

Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Commit 21726a7a "Add assert() for debug assertions" caused build
warnings for all tegra2 based boards:

clock.c:36:1: warning: "assert" redefined
In file included from clock.c:29:
include/common.h:144:1: warning: this is the location of the previous definition

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>

Move the TIMER_ definitions before they are used in KS8695 timer.c code.
Fixes:

timer.c: In function ‘timer_init’:
timer.c:37: error: ‘TIMER_COUNT’ undeclared (first use in this function)
timer.c:37: error: (Each undeclared identifier is reported only once
timer.c:37: error: for each function it appears in.)
timer.c:38: error: ‘TIMER_PULSE’ undeclared (first use in this function)

Signed-off-by: Greg Ungerer <greg.ungerer@opengear.com>

FIX for a typo-bug: The address is stored in PSPR, not PSSR.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>