Add #ifdefs where necessary to not perform relocation fixups.  This
allows boards/architectures which support relocation to trim a decent
chunk of code.

Note that this patch doesn't add #ifdefs to architecture-specific code
which does not support relocation.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

Remove bogus newline character that got added to the .name field of
the disk_partition_t structure.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Commit 574b3195 introduced a subtle bug by mixing a list of tests
for "dev_desc->type" and "dev_desc->if_type" into one switch(), which
then mostly did not work because "dev_desc->type" cannot take any
"IF_*" type values. A later fix in commit 8ec6e332 changed the
switch() into testing "dev_desc->if_type", but at this point the
initial test for unknown device types was completely lost, which
resulted in output like that for IDE ports without device attached:

  Device 1: Model:  Firm:  Ser#:
            Type: # 1F #
            Capacity: not available

This patch re-introduces the missing test for unknown device types.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Tested-by: Stefan Roese <sr@denx.de>

Mflash is fusion memory device mainly targeted consumer eletronic and
mobile phone.
Internally, it have nand flash and other hardware logics and supports
some different operation (ATA, IO, XIP) modes.

IO mode is custom mode for the host that doesn't have IDE interface.
(Many mobile targeted SoC doesn't have IDE bus)

This driver support mflash IO mode.

Followings are brief descriptions about IO mode.

1. IO mode based on ATA protocol and uses some custom command. (read
   confirm, write confirm)
2. IO mode uses SRAM bus interface.

Signed-off-by: unsik Kim <donari75@gmail.com>

This brings in support for the %p modifier which allows us to easily print
out things like ip addresses, mac addresses, and pointers.

It also converts the rarely used 'q' length modifier to the common 'L'
modifier when dealing with quad types.

While this new code is a bit larger (~1k .text), most of it should be made
up by converting the existing ip/mac address code to use format modifiers.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Move the CONFIG_XXX out of the part_XXX.c file and into Makefile to
avoid pointless compiles.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The ending LBA is inclusive. Hence, the partition size should be
((ending-LBA + 1) - starting-LBA) to get the proper partition size.

This is confirmed against the results from the parted tool.
(e.g. use parted /dev/sda -s unit S print) and observe the size.

Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The GUID (Globally Unique Identifier) Partition Table (GPT) is a part
of EFI. See http://en.wikipedia.org/wiki/GUID_Partition_Table



Based on linux/fs/partitions/efi.[ch]

Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>

Signed-off-by: Remy Bohmer <linux@bohmer.net>

Fix output of the usb storage command. It was printing "Device 0: not
available" because IF_TYPE_USB was not included into the switch
statement.

Signed-off-by: Nicolas Lebedenco <nicolas.lebedenco@tasksistemas.com.br>

Use correct field in block_dev_desc_t when writing interface type in
dev_print. Error introduced in 574b3195.

Also added fix from Martin Krause

Signed-off-by: Tor Krill <tor@excito.com>

This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).

Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Detlev Zundel <dzu@denx.de>

Signed-off-by: Detlev Zundel <dzu@denx.de>

- add the SATA framework
- add the SATA command line

Signed-off-by: Dave Liu <daveliu@freescale.com>

This change is in preparation for condtitionial compile support in the
build system.  By spliting them all into seperate lines now, subsequent
patches that change 'COBJS-y += ' into 'COBJS-$(CONFIG_<blah>) += ' will
be less invasive and easier to review

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.

Signed-off-by: Jon Loeliger <jdl@freescale.com>

Signed-off-by: Jon Loeliger <jdl@freescale.com>

This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.

All transformations are of the form:
Before:
    #if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
    #if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)

Signed-off-by: Jon Loeliger <jdl@freescale.com>

                - Show on the Status LEDs, some States of the board.
                - Get the MAC addresses from the EEProm
                - use PREBOOT
                - use the CF on the board.
                - check the U-Boot image in the Flash with a SHA1
                  checksum.
                - use dynamic TLB entries generation for the SDRAM

Signed-off-by: Heiko Schocher <hs@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Include implementations of init_part() and get_partition_info() when
CONFIG_MMC is set.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Since the relocation fix is not included yet and we're not sure how
it will be added, this patch removes code that required relocation
to be fixed for now.

Signed-off-by: Stefan Roese <sr@denx.de>

This patch enables the "new" get_dev() function for block devices
introduced by Grant Likely to be used on systems that still suffer
from the relocation problems (manual relocation neede because of
problems with linker script).

Hopefully we can resolve this relocation issue soon for all platform
so we don't need this additional code anymore.

Signed-off-by: Stefan Roese <sr@denx.de>

Each of the filesystem drivers duplicate the get_dev routine.  This change
merges them into a single function in part.c

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Based on patch by Mike Frysinger, 20 Jun 2006

Modifications are based on the linux kernel approach and
support two use cases:

  1) Add O= to the make command line
  'make O=/tmp/build all'

  2) Set environement variable BUILD_DIR to point to the desired location
  'export BUILD_DIR=/tmp/build'
  'make'

The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'

Command line 'O=' setting overrides BUILD_DIR environent variable.

When none of the above methods is used the local build is performed and
the object files are placed in the source directory.

* Patch by Rune Torgersen, 16 Apr 2004:
  LBA48 fixes

* Patches by Pantelis Antoniou, 16 Apr 2004:
  - Fix some compile problems;
    add "once" functionality for the netretry variable

  - Added LBA48 support (CONFIG_LBA48 & CFG_64BIT_LBA)
  - Added support for 64bit printing in vsprintf (CFG_64BIT_VSPRINTF)
  - Added support for 64bit strtoul (CFG_64BIT_STRTOUL)

* Patch by Masami Komiya, 27 Feb 2004:
  Fix rarpboot: add autoload by NFS

* Patch by Dan Eisenhut, 26 Feb 2004:
  fix flash_write return value in saveenv

* Patch by Stephan Linz, 11 Dec 2003
  expand config.mk to avoid trigraph warnings on NIOS

* Rename "BMS2003" board into "HMI10"

* Cleanup compiler warnings

* Fix problem with side effects in macros in include/usb.h

* Patch by David Benson, 13 Nov 2003:
  bug 841358 - fix TFTP download size limit

* Fixing bug 850768:
  improper flush_cache() in load_serial()

* Fixing bug 834943:
  MPC8540 - missing volatile declarations

* Patch by Stephen Williams, 09 Feb 2004:
  Add support for Xilinx SystemACE chip:
  - New files common/cmd_ace.c and include/systemace.h
  - Hook systemace support into cmd_fat and the partition manager

* Patch by Travis Sawyer, 09 Feb 2004:
  Add bi_opbfreq & bi_iic_fast to 440GX bd_info as needed for Linux

- more documentation for NIOS port
- new struct nios_pio_t, struct nios_spi_t
- Reconfiguration for NIOS Development Kit DK1C20:
  o move board related code from board/dk1c20
    to board/altera/dk1c20
  o create a new common source path board/altera/common
    and move generic flash access stuff into it
  o change/expand configuration file DK1C20.h
- Add support for NIOS Development Kit DK1S10
- Add status LED support for NIOS systems
- Add dual 7-segment LED support for Altera NIOS DevKits

  add FAT support for IDE, SCSI and USB

* Patches by Gleb Natapov, 2 Sep 2003:
  - cleanup of POST code for unsupported architectures
  - MPC824x locks way0 of data cache for use as initial RAM;
    this patch unlocks it after relocation to RAM and invalidates
    the locked entries.

* Patch by Gleb Natapov, 30 Aug 2003:
  new I2C driver for mpc107 bridge. Now works from flash.

* Patch by Dave Ellis, 11 Aug 2003:
  - JFFS2: fix typo in common/cmd_jffs2.c
  - JFFS2: fix CFG_JFFS2_SORT_FRAGMENTS option
  - JFFS2: remove node version 0 warning
  - JFFS2: accept JFFS2 PADDING nodes
  - SXNI855T: add AM29LV800 support
  - SXNI855T: move environment from EEPROM to flash
  - SXNI855T: boot from JFFS2 in NOR or NAND flash

* Patch by Bill Hargen, 11 Aug 2003:
  fixes for I2C on MPC8240
  - fix i2c_write routine
  - fix iprobe command
  - eliminates use of global variables, plus dead code, cleanup.

  (tested with USB memory sticks only)

* Avoid flicker on TRAB's VFD