The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.

The following bootup procedure is used.

At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.

Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
 u-boot.bin image to the RAM from u-boot, and flash to the nand flash
 at address 0xe0000.

* hawkboard_nand_config - Used to generate the secondary
 bootloader(nand_spl) image. This creates an elf file u-boot-spl
 under nand_spl/. Create an AIS signed image using this file, and
 flash it to the nand flash at address 0x20000. The ais file should
 fit in one block.

* hawkboard_uart_config - This is same as the first image, but with
 the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Remove the board_init_f function from nand_spl/nand_boot.c. This
 function is to be defined by all boards using the nand_spl
 functionality in their individual board directory.

 Currently this function was being used by the smdk6400 board. Added
 the board specific function definition.

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

board/davinci.

 Move the davinci common headers to the architecture specific
 include file path.

Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

The patch was already posted to the arago project,
but not yet to mainline. It allows to save environment into
the spi flash. Tested on LogiPD tmdxl138.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Detlev Zundev <dzu@denx.de>
CC: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Detlev Zundev <dzu@denx.de>
CC: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Use the new helper func to clean up duplicate logic handling of the
autostart env var.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

These are pure lookup tables -- no need to be writable.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

No one else needs this table.  While we're here, use the standard
ARRAY_SIZE helper macro.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Many strings in this file need not be writable.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Rather than add runtime overhead of installing completion handlers, do it
statically at build time.  This requires a new build time helper macro to
declare a command and the completion handler at the same time.  Then we
convert the env related funcs over to this.

This gives an opportunity to also unify the U_BOOT_CMD macros.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The duplication of the do_reset prototype has gotten out of hand,
and they're not all in sync.  Unify them all in command.h.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The duplication of the do_bootm prototype has gotten out of hand,
and they're pretty much all outdated (wrt constness).  Unify them
all in command.h.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The recent command clean up to constify the argv option to command funcs
missed the command_t type itself.  This is probably because there are no
build time warnings from it because no one is actually using this thing.
So just punt it rather than fix it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

No need for these structures to be writable or global.

While we're here, also drop local versions of the ARRAY_SIZE macro.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Wolfgang Denk <wd@denx.de>

commit ec50a8e3
"cfi_flash: handle 'chip size exceeds address window' situation"
added 3rd argument to flash_get_size() but didn't fix all the
function calls from the board specific code. Many boards have
their own flash_get_size() definitions in the board code and
use them there, but some boards (e.g. tqm834x, tqm85xx, pdm360ng)
use flash_get_size() from the cfi_flash.c driver.

The bug shows up if the value of the "max_size" argument (which
is not defined when calling the function with two arguments)
happens to be less than "info->size". In this case on the
affected boards we end up with a bank of reduced size and
in the worst case might even be not able to update U-Boot or
to boot the kernel from flash:

=> fli

Bank # 1: CFI conformant FLASH (32 x 16)  Size: 0 kB in 1 Sectors
  AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E
  Erase timeout: 4096 ms, write timeout: 1 ms
  Buffer write timeout: 3 ms, buffer size: 64 bytes

  Sector Start Addresses:
  F0000000   RO

Bank # 2: CFI conformant FLASH (32 x 16)  Size: 128 MB in 512 Sectors
  AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E
  Erase timeout: 4096 ms, write timeout: 1 ms
  Buffer write timeout: 3 ms, buffer size: 64 bytes

  Sector Start Addresses:
  F8000000        F8040000        F8080000        F80C0000        F8100000
  F8140000        F8180000        F81C0000        F8200000        F8240000
  ...

E.g., updating U-Boot is not possible now:

=> protect off ${u-boot_addr} +${u-boot_size}
Error: end address (0xf007ffff) not in flash!
Bad address format
=> era ${u-boot_addr} +${u-boot_size}
Error: end address (0xf007ffff) not in flash!
Bad address format

This patch removes the 3rd argument of flash_get_size() again
and sets "max_size" in the function itself instead of passing
it as a function argument.

Signed-off-by: Anatolij Gustschin <agust@denx.de>

Fix for ARM Relocation support

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Fix for ARM Relocation support

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Fix for ARM Relocation support

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Fix compiler warning

fdt_support.c: In function 'of_bus_default_count_cells':
fdt_support.c:957: warning: passing argument 1 of '__swab32p' discards qualifiers from pointer target type
fdt_support.c:965: warning: passing argument 1 of '__swab32p' discards qualifiers from pointer target type

be32_to_cpup() expects an 'u32 *' while prop is 'const u32 *'.

Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>

This patch fixes the issue by defining and using
CONFIG_SYS_INIT_RAM_SIZE and CONFIG_SYS_INIT_RAM_ADDR.

This patch adopts the
commit 31bfcf1c
from Steve Sakoman and Sandeep Paulraj on Devkit8000.

Signed-off-by: Thomas Weber <weber@corscience.de>

When the cache is enabled in SDRAM we need to flush not only the global
data area but also the bd_info struct in relocate_code. This patch now
flushed the complete dcache (all dcache lines) via flush_dcache() instead
of adding a flush_dcache_range() call for bd_info since this is faster.

Signed-off-by: Stefan Roese <sr@denx.de>

This patch fixes a problem in the Denali (440EPx) SDRAM ECC POST test.
When cache is enabled in the SDRAM area, the values written to SDRAM
need to be flushed from cache to SDRAM using the dcfb instruction.

Without this patch the POST ECC test failed. Now its working again on
platforms with cache enabled in SDRAM.

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Use the return value of cmd_usage instead of ignoring this
and returning a 1.

Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>

Use the return value of cmd_usage instead of ignoring this
and returning a 1.

Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>

Use the return value of cmd_usage instead of ignoring this
and returning a 1.

Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>

Guard strchr/strlen from being called with NULL pointer.
This line is crashing when command "env" is called without subcommand.

The cmd is NULL in this case because the calling function "do_env"
decremented the argc without checking if there are still arguments available.

Signed-off-by: Thomas Weber <weber@corscience.de>

The env command needs one subcommand. If this is not available
print the usage help.

Signed-off-by: Thomas Weber <weber@corscience.de>

update suggested sort command in comment to produce desired order
suggest use of "column -t" to reformat

Signed-off-by: Eric Cooper <ecc@cmu.edu>

* Fix memory initialization. This fixes the problem
  with kernel oopses during heavy load.

* Cleanup pinsetup, which for reference is among
  other things needed for proper flash erasing.

Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>