Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>

...and add to MAKEALL script

Signed-off-by: Wolfgang Denk <wd@denx.de>

This patch adds support for the AT91SAM9RL chip and the AT91SAM9RLEK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This patch adds support for the AT91SAM9261 chip and the AT91SAM9261EK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by
Freescale.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

This patch is based on the port by Mihai Georgian (see linkstation.c for
Copyright information) and implements support for LinkStation / KuroBox HD
and HG PPC models from Buffalo Technology, whereby HD is deactivated at
the moment, pending network driver fixing.

Notice to users: this is pretty much a barebone port. Support for network
on HG models is already in the U-Boot mainline, but you might also want
patches to switch fan / phy modes depending on the negotiated ethernet
parameters. This patch also doesn't support console switching, booting EM
mode, Buffalo specific ext2 magic number. So, if you want to use any of
those, you need additional patches. Otherwise this patche provides a fully
functional u-boot with a network console on your system.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

This patch adds support for the Phytec Phycore-i.MX31 board

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

This patch adds support for the mx31 litekit board

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

Reverting became necessary after it turned out that the patches in
the u-boot-arm repo were modified, and in some cases corrupted.

This reverts the following commits:

	066bebd6
	7a837b73
	c88ae205
	a147e56f
	d6674e0e
	8c8463cc
	c98b47ad
	8bf69d81
	8c16cb0d
	a574a738
	1377b558
	1704dc20

Signed-off-by: Wolfgang Denk <wd@denx.de>

SPARC/LEON2: added support for Gaisler simulator GRSIM/TSIM for SPARC/LEON2 targets. See www.gaisler.com for information.

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>

SPARC/LEON3: added support for GR-CPCI-AX2000 FPGA AX board. The FPGA is exchangeable but a standard LEON3 design is assumed. See www.gaisler.com for information.

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>

SPARC/LEON3: added support for Altera NIOS Development kit (STRATIX II Edition) with GRLIB template design. See www.gaisler.com for information.

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>

SPARC/LEON3: added support for Gaisler GRSIM/TSIM2 SPARC/LEON3 simulatorn. See www.gaisler.com for information.

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>

SPARC/LEON3: added support for GR-XC3S-1500 board with GRLIB template design. See www.gaisler.com for board information.

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>

Support for booting from internal DataFlash, external DataFlash card
or NAND flash is available.

Signed-off-by: Stelian Pop <stelian@popies.net>

This board never went into production

Signed-off-by: Zachary P. Landau <zachary.landau@labxtechnologies.com>
Acked-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>

Signed-off-by: Matthew Fettke <mfettke@videon-central.com>
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: John Rigby <jrigby@freescale.com>

Add some missing ARM boards to MAKEALL.  These build correctly,
unlike several of the boards already listed.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

This patch adds support for the MX31ADS evaluation board from Freescale,
initialization code is copied from RedBoot sources, also provided by Freescale.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

This patch adds support for the Phytec Phycore-i.MX31 board

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

This patch adds support for the mx31 litekit board

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>

Signed-off-by: Peter Pearse <peter.pearse@arm.com>

R2D plus is SH reference board used with SH7751R.
This board has 266Mhz CPU, 64MB SDRAM, Cardbus, CF interface,
one PCI bus, VGA, and two Ethernet controller.

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Renesas Solutions R7780MP is a reference board on SH7780.
This board has serial, 10/100 base Ethernet deivice, CF slot
and VGA devices. This board can set extension board.
Extension board has 10/100/1000 base Ethernet device, PCI slot,
S-ATA, iDVR slot.

Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Migo-R is a board based on SH7722 and has may devices.
In this patch, supported SCIF, NOR flash and Ethernet.

Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:

- 4 ethernet ports instead of 2
- no SATA port
- no USB port

Currently EMAC2+3 are not working. This will be fixed in a later
release.

Signed-off-by: Stefan Roese <sr@denx.de>

460EX doesn't support a fixed bootstrap option to boot from 512 byte page
NAND devices. The only bootstrap option for NAND booting is option F for
2k page devices. So to boot from a 512 bype page device, the I2C bootstrap
EEPROM needs to be programmed accordingly.

This patch adds basic NAND booting support for the AMCC Canyonlands aval
board and also adds support to the "bootstrap" command, to enable NAND
booting I2C setting.

Tested with 512 byte page NAND device (32MByte) on Canyonlands.

Signed-off-by: Stefan Roese <sr@denx.de>

This patch adds support for the AMCC Canyonlands 460EX evaluation
board.

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Kimmo Leppala / Sysart and
Timo Tuunainen / Sysart

Signed-off-by: Stelian Pop <stelian@popies.net>

Add support for the ATNGW100 Network Gateway reference design,
including flash, ethernet and MMC support.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Hi,

The patch adds 4 boards, called AcTux-1 .. AcTux-4. This patch contains the
files that
contain changes for multiple boards, the board-specific files follow as
separate patches.

Signed-off-by: Michael Schwingen <michael@schwingen.org>