Now that the boards.cfg file supports options to mkconfig, we can move
the bf527-ezkit-v2 target out of the Makefile and into boards.cfg.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

We also have to relocate the onenand command table manually, otherwise
onenand command don't work.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>

SICRH has been misconfigured, i.e. TSEC2 clock + D[0:3] are GPIOs.
Fix this to be RGMII signals again.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>

Since we use hwconfig in cases before relocation (like getting DDR
params on FSL PPC systems), we can have strings that exceed the early
small (32 byte) buffer size that getenv will handle.

So we explicitly allocate our own buffer on the stack and use if to
handle getting the hwconfig env string.  We currently utilize a string
length of 128 bytes.

This allows us to get rid of boot messages like:

env_buf too small [32]

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

With debug the follow is printed:
  => saveenv
  Saving Environment to Flash...
  Data to save 0x18000
  Data (start 0xfff48000, len 0x18000) saved at 0x7fe63f20
  Protect off FFF40000 ... FFF5FFFF
  Un-Protected 1 sectors
  Erasing Flash...
  . done
  Erased 1 sectors
  Writing to Flash... Restoring the rest of data to 0xfff48000 len 0x18000
  done
  Protected 1 sectors
  =>

Without debug:
  => saveenv
  Saving Environment to Flash...
  Un-Protected 1 sectors
  Erasing Flash...
  . done
  Erased 1 sectors
  Writing to Flash... done
  Protected 1 sectors
  =>

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

This patch adds CONFIG_SYS_FLASH_BANKS_SIZES define to make use of new
cfi_flash driver ability to detect flash chips that are bigger than a
corresponding address window (we have such situation on some revs of
a4m072).

Signed-off-by: Ilya Yanok <yanok@emcraft.com>

On some boards we have flash mapped high in the address space with
considerably small window (say 0xFE000000 and 32MB). When we install
bigger chip (say 64MB) on such a board strange things happen
(flash_write() doesn't work at all, for ex). That's because cfi_flash
driver doesn't care about window size at all.
Of course, cleanest solution would probably be to just extend address
window to be able to map the whole flash but for legacy/compatibility
reasons some people prefer just truncate the flash size and never use
the upper part.
This patch adds an option for cfi_flash driver to handle this situation
properly. To achieve this we add the new function cfi_flash_bank_size()
which can be provided by the board code and weak-aliased to default
implementation that returns value from the CONFIG_SYS_FLASH_BANKS_SIZES
array if it's defined or 0 otherwise (the last case is added for
compatibility).
If non-zero flash bank size is provided and detected chip size is bigger
than provided address window size the warning will be displayed and
flash chip will be truncated.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>

Changed cfi_flash_bank_size() return type to unsigned long
to match caller function.
Signed-off-by: Wolfgang Denk <wd@denx.de>

This patch solves a problem with USB hanging under higher load on a
i.MX31 board.  It falls into class of typical USB problems and fixes:
if you don't understand the real cause, add a delay somewhere.

The problem appeared after introduction of ELF relocation, which
results in smaller code, which appears to run faster (probably because
it fits better in the cache); turning off the instruction cache,
adding debug printf()s and increasing the delay have all been found to
make the problem go away.

Moving the original "udelay(1)" up in the code to it's new place made
the problem appear much less frequently. Increasing the delay to 2
microseconds then made the code run reliably in all (hour-long) tests.
To be on the safe side, we set it to 5 microseconds here.

Signed-off-by: Heiko schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

These ep and root hub structures need not be writable.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Commit 3ed16071 "USB: sync Queue Element Transfer Descriptor against
EHCI spec" added an "__attribute__ ((aligned (32)))" to the
declaration of struct qTD, as used for example in the Linux kernel as
well.

However, it turns out that this attribute causes errors in "usb start"
(like "ERROR: NOT USB_CONFIG_DESC 7b" and similar). Drop the attribute
again.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>

It is useful to know the EHCI-PCI hccr, hcor and hc_lenght to make sure it was
successfully registered, and at the correct location.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

This patch solves a problem with USB hanging under higher load on a
i.MX31 board.  It falls into class of typical USB problems and fixes:
if you don't understand the real cause, add a delay somewhere.

The problem appeared after introduction of ELF relocation, which
results in smaller code, which appears to run faster (probably because
it fits better in the cache); turning off the instruction cache,
adding debug printf()s and increasing the delay have all been found to
make the problem go away.

Moving the original "udelay(1)" up in the code to it's new place made
the problem appear much less frequently. Increasing the delay to 2
microseconds then made the code run reliably in all (hour-long) tests.
To be on the safe side, we set it to 5 microseconds here.

Signed-off-by: Heiko schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>

Initial support for Extreme Engineering Solutions XPedite5500 -
a P2020-based PMC/XMC single board computer.

Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add memory and I2C posts to the XPedite517x/520x/537x board families.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The PIC's TFRR register doesn't affect hardware and is generally unused,
so use as storage for the POST word.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add the ability to not report an I2C POST error for a set of given I2C
addresses on bootup.  This is useful for cases when a device may or may
not be present, and neither case is considered an error.  For example:

- Some form factors such as XMC and Compact PCI Express have an I2C
  EEPROM whose address changes based on geographical address.  Eg
  installed in one slot its EEPROM address is, 0x50, in another its
  0x51, etc.  This allows multiple devices to have their EEPROMs present
  on the same I2C bus.  Thus the I2C devices present for an XMC or
  CPCIe card depend on if and where other cards are installed in the
  same system.

- Some cards have optional I2C devices.  Eg one hardware build
  configuration has different I2C devices than another and software
  can't determine if the optional device should be present or not.

- Some cards have optional daughtercards with I2C devices on them.

- I2C EEPROMs address range depends on their size.  Its possible to
  support differently size EEPROMs by only probing the EEPROM's base
  address and ignoring the other addresses that are impacted by its
  size.

A new CONFIG_SYS_POST_I2C_IGNORES define has been added which specifies
a list of I2C addresses for the I2C POST to ignore.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

According to the I2C specification device address 0 is the "general call
address", ie a broadcast address.  The I2C specification states that the
format of a general call uses at least 2 bytes, which U-Boot's probing
routine does not adhere to.

Not probing device address 0 will prevent possible issues with devices
that accept general calls.  Additionally, this change shouldn't reduce
POST coverage since each I2C device should still be accessed via its
own, unique address.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The logic previously used in the I2C post was a bit convoluted.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

- Clean up ifdeffery
- Update coding style

No functional change should have occurred.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Some U-Boot images for X-ES boards support multiple products in the same
family.  For example, the XPedite5370, XPedite5371, and XPedite5372 are
similar enough that one U-Boot image can work on all 3 cards.  To make it
clear that a U-Boot image can work on boards of the same family, rename
the boards with the least significant digit of 'x'.

While we're at it, change the board config file and make targets to be
lowercase.

Also change the default uImage and fdt filenames to "board.uImage" and
"board.dtb" to be more generic.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add board_flash_wp_on() to check a pca9557 gpio pin to see
if non-volatile memory write protection is enabled.

Previously, write protected NOR flashes would fail initialization which
resulted in a bootup error such as:

 ...
 DTT:   53 C local / 64 C remote (adt7461@4c)
 DTT:   54 C local (ds1621@48)
 FLASH: Executed from FLASH1
 POST memory PASSED
 FLASH: ## Unknown FLASH on Bank 1 - Size = 0x00000000 = 0 MB
 ## Unknown FLASH on Bank 2 - Size = 0x00000000 = 0 MB
 *** failed ***
 ### ERROR ### Please RESET the board ###

With this patch, NOR flash initialization is skipped:

 ...
 DTT:   53 C local / 64 C remote (adt7461@4c)
 DTT:   54 C local (ds1621@48)
 FLASH: Executed from FLASH1
 POST memory PASSED
 FLASH: Uninitialized - Write Protect On
 L2:    1024 KB enabled
 NAND:  1024 MiB
 ...

Note that flash related commands such as flinfo and saveenv will error
out when flash write protection is enabled.

Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Create a common checkboard() function to support all X-ES's Freescale
boards.

Also, add a get_board_derivative() function which reads hardware
strapping resistors to determine what model a board is.  This allows one
U-Boot image to support multiple boards.

Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add a new 'pci enum' command which re-enumerates the PCI buses.  This
command is enabled via the CONFIG_CMD_PCI_ENUM define and can be useful
in boards with FPGAs connected via PCI/PCIe, boards that support PCI
hot-plugging, or during PCI debug.

Also enable the 'pci enum' command for X-ES's Freescale-based boards.

Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>

Common Freescale code for PCI initialization now exists, so migrate X-ES
boards to use it.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The recent change the env code added an additional 32 bytes into gd_t
and that causes to grow pass the previous CONFIG_SYS_GBL_DATA_SIZE size.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This board is broken and it's not possible to repair it.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

This board is broken and impossible to repair without deep knowledge or
availability of the hardware.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>