Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Sigend-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Domen Puncer <domen.puncer@telargo.com>

Signed-off-by: Stefan Roese <sr@denx.de>

Now 405EZ ports also show upon bootup from which boot device
they are configured to boot:

U-Boot 1.2.0-gd3832e8f-dirty (Apr 18 2007 - 07:47:05)

CPU:   AMCC PowerPC 405EZ Rev. A at 199.999 MHz (PLB=133, OPB=66, EBC=66 MHz)
       Bootstrap Option E - Boot ROM Location EBC (32 bits)
       16 kB I-Cache 16 kB D-Cache
Board: Acadia - AMCC PPC405EZ Evaluation Board

Signed-off-by: Stefan Roese <sr@denx.de>

U-Boot part of Lite5200b low power mode support.
Puts SDRAM out of self-refresh and transfers control to
address saved at physical 0x0.

Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>

Use "setter" functions instead of flags, cleaner and more flexible.
It also fixes the problem noted by Timur Tabi that the ethernet MAC
addresses were all being set incorrectly to the same MAC address.

In bootm, create the "/chosen" node only if it doesn't already exist
  (better matches the previous behavior).
Update for proper reserved memory map handling for initrd.

Set up the portmux for the MMC interface and enable the MMC driver
along with support for DOS partitions, ext2 and FAT filesystems.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Driver for the Atmel MCI controller (MMC interface) for AT32AP CPUs.

The AT91 ARM-based CPUs use basically the same hardware, so it should
be possible to share this driver, but no effort has been made so far.

Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from

http://www.atmel.com/dyn/products/datasheets.asp?family_id=682



Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Implement functions for configuring the mmci pins, as well as
functions for getting the clock rate of the mmci controller.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Include implementations of init_part() and get_partition_info() when
CONFIG_MMC is set.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Implement MACB initialization for AVR32 and ATSTK1000, and turn
everything on, including the MACB driver.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Driver for the Atmel MACB on-chip ethernet controller.

This driver has been tested on the ATSTK1000 board with a AT32AP7000
CPU. It should probably work on AT91SAM926x as well with some minor
modifications.

Hardware documentation can be found in the AT32AP7000 data sheet,
which can be downloaded from

http://www.atmel.com/dyn/products/datasheets.asp?family_id=682



Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Implement functions for configuring the macb0 and macb1 pins, as
well as functions for getting the clock rate of the various
busses the macb ethernet controllers are connected to.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Implement dma_alloc_coherent() which returns cache-aligned
uncacheable memory.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Instead of creating yet another set of MII register definitions
in the macb driver, here's a complete set of definitions for everyone
to use.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Include the imi, imls and jffs commands sets by default on ATSTK1000.
Also define CONFIG_BOOTARGS to something more useful, define
CONFIG_BOOTCOMMAND and enable autoboot by default.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Copy the definition of struct stat from the Linux kernel.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Conform to the "standard" interface and use initdram() instead of
board_init_memories() on AVR32. This enables us to get rid of the
sdram_size member of the global_data struct as well.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Relocate the u-boot image into SDRAM like everyone else does. This
means that we can handle much larger .data and .bss than we used to.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Rewrite the resource management code (i.e. I/O memory, clock gating,
gpio) so it doesn't depend on any global state. This is necessary
because this code is heavily used before relocation to RAM, so we
can't write to any global variables.

As an added bonus, this makes u-boot's memory footprint a bit smaller,
although some functionality has been left out; all clocks are enabled
all the time, and there's no checking for gpio line conflicts.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Convert spaces to tabs (must have missed this one last time around),
sort the entries by address and group them together by bus
connectivity.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Add -fPIC -mno-init-got to the avr32-specific CFLAGS to make u-boot
position independent. This will make relocation a lot easier.

-mno-init-got means that gcc shouldn't emit code to load the GOT
address into r6 in every function prologue. We do it once and for
all in the early startup assembly code, so enabling this option
makes u-boot a bit faster and smaller.

The assembly parts have always been position-independent, so no code
changes should be necessary.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

It doesn't really matter which toolchain you use to compile u-boot,
but the avr32-linux one is probably what most people have installed.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>