Atmel DataFlashes by default operate with pages that are slightly bigger
than normal binary sizes (i.e. many are 1056 byte pages rather than 1024
bytes).  However, they also have a "power of 2" mode where the pages show
up with the normal binary size.  The latter mode is required in order to
boot with a Blackfin processor, so many people wish to convert their
DataFlashes on their development systems to this mode.  This standalone
application does just that.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The recent 52cb4d4f commit which renamed device to stdio_dev missed the
cm-bf548's video board.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Since the NAND code now uses 64bit code, make sure we enable support for
ADI Blackfin boards in printf to avoid the warning:
nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF for correct output!

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

If the memory layout pushes the stack out of the default DCPLB coverage,
the exception handler may trigger a double fault by trying to push onto
the uncovered stack.  So handle the exception stack similar to the kernel
by using the top of the scratch pad SRAM.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The default console size indirectly applies to length of env vars, so a
smaller length makes it hard to pass longer command lines to kernels.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The display_global_data() function generated warnings with pretty much
every variable.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>

The CM-BF537U is similar to the CM-BF537E module, but enough to need its
own board port.

Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Since the Blackfin ABI favors higher scratch registers by default, use the
last scratch register (P3) for global data rather than the first (P5).
This allows the compiler's register allocator to use higher number scratch
P registers, which in turn better matches the Blackfin instruction set,
which reduces the size of U-Boot by more than 1024 bytes...

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Add dns and ntp to default networking commands, and ask for more dhcp
options to better configure the network environment.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

DM646x is an SOC from TI which has both an ARM and a DSP.
There are multiple variants of the SOC mainly dealing with different
core speeds.
This patch adds the initial framework for the DM646x SOC.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

The Default mode that is built for the Davinci DVEVM happens
to be the NOR mode.
When we want to build for the NAND mode, we get a compilation
error. This is overcome by defining the CONFIG_MTD_DEVICE
flag in the NAND mode.
The image built for NAND mode was successfully tested on the
DaVinci DM6446 EVM.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

v7_flush_dcache_all, because it depends on omap ROM code is not
generic.  Rename the function to 'invalidate_dcache' and move it
to the omap cpu directory.

Collect the other omap cache routines l2_cache_enable and
l2_cache_disable with invalide_dcache into cache.S.  This
means removing the old cache.c file that contained l2_cache_enable
and l2_cache_disable.

The conversion from cache.c to cache.S was done most through
disassembling the uboot binary.  The only significant change was
to change the comparision for the return of get_cpu_rev from

   cmp	r0, #0
   beq	earlier_than_label

Which was lost information to

   cmp	r0, #CPU_3XX_ES20
   blt	earlier_than_label

The paths through the enable routine were verified by
adding an infinite loop and seeing the hang.  Then
removing the infinite loop and seeing it continue.

The disable routine is similar enough that it was not
tested with this method.

Run tested by cold booting from nand on beagle and zoom1.
Compile tested on MAKEALL arm.

Signed-off-by: Tom Rix <Tom.Rix@windriver.com>

This patch removes the asm/sizes.h header file from being
included in the DaVinci SOC configs.
References to SZ_xx have been replaced by appropriate
bit shifted values.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Wolfgang Denk <wd@denx.de>

This patch adds support for the DM365 EVM.
It has been tested on a DM365 EVM.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

This patch adds support for DaVinci DM365 SOC.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Signed-off-by: Ilko Iliev <iliev@ronetix.at>

This patch adds support for the DevKit8000 board.

Signed-off-by: Frederik Kriewitz <frederik@kriewitz.eu>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The Calao TNY-A9260 and TNY-9G20 are boards manufactured and sold by
Calao Systems <http://www.calao-systems.com

>. Their components are very
similar to the AT91SAM9260EK board, so their configuration is based on
the configuration of this board. There are however some differences:
different clocks, no LCD, no ethernet. They also can use SPI EEPROM to
store the environment.

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This feature can be used to trigger special command "sysrstcmd" using
reset key long press event and environment variable "sysrstdelay" is set
(useful for reset to factory or manufacturing mode execution)

Kirkwood SoC implements a hardware-based SYSRSTn duration counter.
When SYSRSTn is asserted low, a SYSRSTn duration counter is running.
The counter value is stored in the SYSRSTn Length Counter Register
The counter is based on the 25-MHz reference clock (40ns)
It is a 29-bit counter, yielding a maximum counting duration of
2^29/25 MHz (21.4 seconds). When the counter reach its maximum value,
it remains at this value until counter reset is triggered by setting
bit 31 of KW_REG_SYSRST_CNT

Implementation:
Upon long reset assertion (> ${sysrstdelay} in secs) sysrstcmd will be
executed if pre-defined in environment variables.
This feature will be disabled if "sysrstdelay" variable is unset.

for-ex.
setenv sysrst_cmd "echo starting factory reset;
		   nand erase 0xa0000 0x20000;
		   echo finish ed sysrst command;"
will erase particular nand sector if triggered by this event

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>

The Calao SBC35-A9G20 board is manufactured and sold by Calao Systems
<http://www.calao-systems.com>. It is built around an AT91SAM9G20 ARM SoC
running at 400MHz. It features an Ethernet port, an SPI RTC backed by an onboard
battery , an SD/MMC slot, a CompactFlash slot, 64Mo of SDRAM, 256Mo of NAND
flash, two USB host ports, and an USB device port. More informations can be
found at <http://www.calao-systems.com/articles.php?lng=en&pg=5936

>

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>

This patch adds support for i.MX27-LITEKIT development board from
LogicPD. This board uses i.MX27 SoC and has 2MB NOR flash, 64MB NAND
flash, FEC ethernet controller integrated into i.MX27.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Denk <wd@denx.de>

Commit 7ebafb7e introduced a mistake in the spi
init function call for those boards. This patch fixes this.

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>

Remove duplicate set_cr

set_cr is defined in both asm-arm/proc-armv/system.h and
include/asm-arm/system.h. This patch removes it (and some duplicate
defines) from the former.

Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>

Update CHANGELOG

Signed-off-by: Wolfgang Denk <wd@denx.de>

This fixes current build failure.

Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>

mvblm7.c: fix warning: implicit declaration of function
'mv_reset_environment'

Signed-off-by: Wolfgang Denk <wd@denx.de>

The "console: unify printing current devices" patch goofed:
CONFIG_SYS_CONSOLE_INFO_QUIET is supposed to *REMOVE* boot
time noise, not add it.  Said patch changed the #ifndefs
to #ifdef; this one restores them to the proper sense.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>

The "mac id" command took a 4-character parameter as the identifier string.
However, for any given board, only one kind of identifier is acceptable, so it
makes no sense to ask the user to type it in.  Instead, if the user enters
"mac id", the identifier (and also the version, if it's NXID) will
automatically be set to the correct value.

Improve the message that is displayed when EEPROM is read during boot.  It now
displays "EEPROM:" and then either an error message or the EEPROM identifier
if successful.

If the identifier in EEPROM is valid, then always reject a bad CRC, even if the
CRC field has not been initialized.

Don't force the MAC address count to MAX_NUM_PORTS or less.  Forcing the value
to be changed resulting in an in-memory copy that does not match what's in
hardware, even though the user did not request that change.

Finally, always update the CRC value in the in-memory copy after any field
is changed, so that the CRC is always correct.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Call fsl_pci_init_port() to initialize all the PCIe ports on the board.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

fsl_pci_init_port can be called from board specific PCI initialization
routines to setup the PCI (or PCIe) controller.  This will reduce code
redundancy in most of the 85xx/86xx FSL board ports that setup PCI.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The MPIC initialization code for Freescale e500 CPUs was not using I/O
accessors, and it was not issuing a read-back to the MPIC after setting
mixed mode.  This may be the cause of a spurious interrupt on some systems.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

P1011 and P2010 are single core variants of P1010 and P2020 respectively.
The board(RDB) will be same.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

P1011 - Single core variant of P1020
P2010 - Single core variant of P2020

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>