This patch brings the PMC440 board configuration file.
Finally it enables the PMC440 board support.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

This board never left prototyping state and it
became a millstone round my neck. So remove it.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>

These patches add support for the PPC440EPx-based "Korat" board to
U-Boot.  They are based primarily on support for the Sequoia board.

Signed-off-by: Larry Johnson <lrj@acm.org>

ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU,
which is a derivative of AT32AP7000.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU,
which is a derivative of AT32AP7000.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>

This patch adds NAND booting support for the AMCC 405EX(r) eval boards.
Again, only one image supports both targets.

Signed-off-by: Stefan Roese <sr@denx.de>

The Haleakala is nearly identical with the Kilauea eval board. The only
difference is that the 405EXr only supports one EMAC and one PCIe
interface. This patch adds support for the Haleakala board by using
the identical image for Kilauea and Haleakala. The distinction is done
by comparing the PVR.

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

Add MPC8360EMDS_ATM_config and MPC832XEMDS_ATM_config into
Makfile and MAKEALL

Signed-off-by: Tony Li <tony.li@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>

Changes to the TSEC driver affect almost all 83xx, 85xx, and 86xx boards.
Now we can do a MAKEALL test on all of them!

Signed-off-by: Andy Fleming <afleming@freescale.com>

Signed-off-by: Stefan Roese <sr@denx.de>

and reorder the existing 83xx maintainers alpha.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Stefan Roese <sr@denx.de>

..by placing board entries one per line, as suggested by jdl.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Add support for Wind River's SBC8641D reference board.

Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Jon Loeliger <jdl@freescale.com>

Add support for the following DaVinci boards:
- DV_EVM
- SCHMOOGIE
- SONATA

Changes:

- Split into separate board directories
- Removed changes to MTD_DEBUG (or whatever it's called)
- New CONFIG_CMD party line followed
- Some cosmetic fixes, cleanup etc.
- Patches against the latest U-Boot tree as of now.
- Fixed CONFIG_CMD_NET in net files.
- Fixed CONFIG_CMD_EEPROM for schmoogie.
- Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and
   DV_EVM. Can't check if it works on SONATA, don't have a board any more,
   but it at least compiles.

Here is an excerpt from session log on SCHMOOGIE...

U-Boot 1.2.0-g6c33c785-dirty (Aug  7 2007 - 13:07:17)

DRAM:  128 MB
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
ARM Clock : 297MHz
DDR Clock : 162MHz
ETH PHY   : DP83848 @ 0x01
U-Boot > iprobe
Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F
U-Boot > ping 192.168.253.10
host 192.168.253.10 is alive
U-Boot >

Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Zach Sadecki <Zach.Sadecki@ripcode.com>
Acked-by: Stefan Roese <sr@denx.de>

Signed-off-by: Stefan Roese <sr@denx.de>

This series of patches adds support for 2 boards from Netstal Maschinen.

The HCU4 has a PPC405Gpr and
the HCU5 has a PPC440EPX.

The HCU4 has a somehow complicated flash setup, as the booteprom is
only 8 bits and the CFI 16 bits wide, which makes it impossible to use a more
elegant solution.

The HCU5 has only a booteprom as the whole code will be downloaded from a
different board which has HD, CD-ROM, etc and where all code is stored.

This is my third try. I incorporated all suggestions made by Wolfgang and Stefan.
Thanks them a lot.

Signed-off-by: Niklaus Giger <niklaus.giger@netstal.com>

Add the ability for modules from the Schindler cm5200 family to use a
single U-Boot image:
- rename cm1_qp1 to cm5200
- add run-time module detection
- parametrize SDRAM configuration according to the module we are running on

Few minor, board-specific fixes included in this patch:
- better MAC address handling
- updated default environment ('update' command uses +{filesize} now)
- improved error messages in the auto-update code
- allow booting U-Boot from RAM (CFG_RAMBOOT)

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

The following MPC5121e subsystems are supported:

- low-level CPU init
- NOR Boot Flash (common CFI driver)
- DDR SDRAM
- FEC
- I2C
- Watchdog

Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
Signed-off-by: Jan Wrobel <wrr@semihalf.com>

Signed-off-by: John Otken <john@softadvances.com>

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>

Changed MAKEALL file mode to executable, removed executable file mode from Makefile

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>

It was missing from the original port submission.

Signed-off-by: Jon Loeliger <jdl@freescale.com>

Added board/freescale/m5329evb, cpu/mcf532x, drivers/net,
drivers/serial,  immap_5329.h, m5329.h, mcfrtc.h,
include/configs/M5329EVB.h, lib_m68k/interrupts.c, and
rtc/mcfrtc.c

Modified CREDITS, MAKEFILE, Makefile, README, common/cmd_bdinfo.c,
common/cmd_mii.c, include/asm-m68k/byteorder.h, include/asm-m68k/fec.h,
include/asm-m68k/io.h, include/asm-m68k/mcftimer.h,
include/asm-m68k/mcfuart.h, include/asm-m68k/ptrace.h,
include/asm-m68k/u-boot.h, lib_m68k/Makefile, lib_m68k/board.c,
lib_m68k/time.c, net/eth.c and rtc/Makefile

Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>

This patch adds initial support for the Liebherr lwmon5 board euqipped
with an AMCC 440EPx PowerPC.

Signed-off-by: Stefan Roese <sr@denx.de>

This patch adds NAND booting support for the AMCC Acadia eval board.

Please make sure to configure jumper J7 to position 2-3 when booting
from NOR, and to position 1-2 when booting for NAND.

I also added a board command to configure the I2C bootstrap EEPROM
values. Right now only 267MHz is support for booting either via NOR
or NAND FLASH. Here the usage:

=> bootstrap 267 nor	;to configure the board for 267MHz NOR booting
=> bootstrap 267 nand	;to configure the board for 267MHz NNAND booting

Signed-off-by: Stefan Roese <sr@denx.de>

This patch adds NAND booting support for the AMCC Bamboo eval board.
Since the NAND-SPL boot image is limited to 4kbytes, this version
only supports the onboard 64MBytes of DDR. The DIMM modules can't be
supported, since the setup code for I2C DIMM autodetection and
configuration is too big for this NAND bootloader.

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Jon Loeliger <jdl@freescale.com>