The ECC calculations were started by writing 1 << 13 to the nand FCR register;
that value is also defined as DAVINCI_NANDFCR_4BIT_CALC_START in emif_defs.h.

This patch substitutes the macro DAVINCI_NANDFCR_4BIT_CALC_START for the
magic number '1 << 13'.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

The IGEP module is a low-power, high performance production-ready
system-on-module (SOM) based on TI's OMAP3 family.The IGEP module
solution based upon TI OMAP3 provides a low-power/low-cost platform
for a variety of consumer/industrial/medical devices.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

The IGEP v2 board is a low-cost, fan-less and industrial temperature
range single board computer that unleashes laptop-like performance and
expandability without the bulk, expense, or noise of typical desktop
machines. Its architecture shares much in common with other OMAP3 boards.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

Introduce Numonyx DDR timings and provide CONFIG_OMAP3_NUMONYX_DDR
config options to allow for platform files to setup their timings.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

This patch fixes the build breakage introduced by the recent relocation
changes for ARMV7

Signed-off-by: Steve Sakoman <steve@sakoman.com>

This patch fixes a typo in the routine to calculate the cs offset
based upon the contents of the SDRC cs_cfg register.  This function
mistakenly shifts the CS1STARTLOW field 17 bits right instead of
17 bits left.

This hasn't been an issue to date because all OMAP3 boards currently
are configured to have zeros in this field.

Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>

Signed-off-by: Steve Sakoman <steve@sakoman.com>

This patch fixes the build breakage introduced by the recent relocation
changes for ARMV7

Signed-off-by: Steve Sakoman <steve@sakoman.com>

The SDP4430 does not have onboard NAND, it has eMMC on the second
MMC slot.  This patch adds support for saving the u-boot environment
to eMMC.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>

This patch switches from the legacy mmc driver to the new generic mmc driver

Signed-off-by: Steve Sakoman <steve@sakoman.com>

This patch switches from the legacy mmc driver to the new generic mmc driver

Signed-off-by: Steve Sakoman <steve@sakoman.com>

This patch switches from the legacy mmc driver to the new generic mmc driver

Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>

This patch switches from the legacy mmc driver to the new generic mmc driver

Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>

OMAP boards currently use a legacy mmc driver. This patch adds a new
mmc driver which will work with the generic mmc driver in u-boot.

This new driver will work with both OMAP3 and OMAP4 boards.

This patch does not remove the old driver.  It should remain in the
tree until all boards that use it switch to the new driver.

Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>

  The current mmc driver returns erroneous capacity information for
  eMMC.  The capacity of eMMC devices is available only in the ext-CSD
  register.  This patch add code to read the ext-CDSD register and
  correctly calculate eMMC capacity.

Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Acked-by: Steve Sakoman <steve@sakoman.com>

TI hasn't reserved a USB Product ID for gadgets, so use the default
vendor and product ID to avoid confusion.

Signed-off-by: Steve Sakoman <steve@sakoman.com>

Signed-off-by: Loic Minier <loic.minier@linaro.org>
CC: stefano babic <sbabic@denx.de>

The crash was occuring in env_relocate because it was being called prior
to mmc_initialize.  This patch moves the MMC initialization earlier in
the init process.

This patch also cleans up the env_relocate_spec code in env_mmc.c

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Acked-by: Stefano Babic <sbabic@denx.de>

Fix build error introduced in beca5a5f

common/libcommon.a(fdt_support.o): In function `fdt_add_edid':
/local/hudson/jobs/mirrors-u-boot.git/workspace/common/fdt_support.c:1205: undefined reference to `fdt_increase_size'
make: *** [u-boot] Error 1

Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>

Signed-off-by: Stefano Babic <sbabic@denx.de>

The patch adds the EHCI controller for the i.MX31 Soc.

Signed-off-by: Stefano Babic <sbabic@denx.de>

The patch adds a utility function and defines
to set the pad as it is done in linux.

Signed-off-by: Stefano Babic <sbabic@denx.de>

The patch adds the possibility to update the QONG
FPGA (a Lattice XP2-5E) with u-boot using some GPIOs
to drive the JTAG interface.

Signed-off-by: Stefano Babic <sbabic@denx.de>

Signed-off-by: Stefano Babic <sbabic@denx.de>

The patch adds support to load a Lattice's bitstream
image (called VME file) into a Lattice FPGA. The code
containing the state machine delivered as part of
Lattice's ispVMtools is integrated.

The FPGA is programmed using the JTAG interface. The
board maintainer must provide accessors to drive the
JTAG signals TCK, TMS, TDI and to get the value of the
input signal TDO.

Signed-off-by: Stefano Babic <sbabic@denx.de>

This is a change similar to what is already in the Linux driver.  We
should only program the CLRDATATOG bit when the current mode indicates
that it is needed.

Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>

This patch changes `usb_stor_scan' to scan all the LUNs of each mass
storage device.  It also fixes the various commands to correctly set
the LUN field.

Notably, it allows each LUN of GuruPlug's microSD card reader to be
accessed.

Signed-off-by: Ludovic Courtès <ludo@gnu.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>

After gadget reinitializaton (after tftp has been done once)
packet_received may become equal to 1 due to nuking OUT_EP
while disabling it in eth_reset_config.

rx_submit called from usb_eth_init queues rx_req first time.
But the first call of usb_eth_recv from NetLoop queues rx_req
again due to packet_received = 1.

The following flow shows the path of functions calls when
this happens:

 net/net.c:NetLoop
 |
 +-net/eth.c:eth_init
 |   ether.c:usb_eth_init
 |   |
 |   +-udc_driver:usb_gadget_handle_interrupts
 |   |   udc_driver:...
 |   |     ether.c:eth_setup
 |   |       ether.c:eth_set_config
 |   |         ether.c:eth_reset_config
 |   |           udc_driver:usb_ep_disable
 |   |             udc_driver:nuke
 |   |               ether.c:rx_complete
 |   |                 ether.c: packet_received = 1;
 |   |
 |   +-ether.c:rx_submit
 |       udc_driver:usb_ep_queue --- The first time when rx_req is queued
 |
 +-net/eth.c:eth_rx
     ether.c:usb_eth_recv
     |
     +-udc_driver:usb_gadget_handle_interrupts
     |   udc_driver:... --- no interrupts, returning
     +-ether.c: if (packet_received) { ...
         ether.c:rx_submit
           udc_driver:usb_ep_queue --- The second time!

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>

Remove and fix needless and destructive operations with tx/rx_req.

1) 'req' in rx_complete is always not NULL and always equals to rx_req
2) Free allocated tx_req if rx_req allocation has failed
3) Do not zero out tx/rx_req in usb_eth_init, leave this for
eth_reset_config which will be called at the next use of usb0
4) Additional check in usb_eth_recv is not required

Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>

This fixes TIMEOUT with my Kingston 32GB USB3.0 flashdrive, which I experienced
on my PXA270 (USB 1.1) Vpac270 board.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>

This patch fixes an error when running MAKEALL for ARM9.

On OS X /bin/sh uses builtin echo which does not utilise '-n' switch.
GNU manual for builtins recomend to use here-document style to solve
this portability issue.

This patch removes the usage of 'echo -n' and replace by here-document
style or a oneline echo command.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
CC: Peter Pearse <peter.pearse@arm.com>

The pl01x serial driver was lacking the code to switch baudrates from the
command line.  Fixed by simply saving the new baudrate and calling
serial_init() again.  Also fixed CamelCase variables, I/O accessors and
comment style.

Signed-off-by: Matt Waddel <matt.waddel@linaro.org>

Adds support for the ARM quad-core Cortex-A9 processor

This system includes a motherboard(Versatile Express), daughterboard
(Coretile), and SOC(Cortex-A9 quad core).  The serial port, ethernet,
and flash systems work with these additions.  The naming convention
is:
   SOC -> CortexA9 quad core = ca9x4
   daughterboard -> Coretile = ct
   motherboard -> Versatile Express = vxp
This gives ca9x4_ct_vxp.c as the board support file.

Signed-off-by: Matt Waddel <matt.waddel@linaro.org>

Merge several sizes.h in asm/arch subdirectories into a single
asm/sizes.h file.

Fixup usage of asm/arch/sizes.h in some files to use the merged file.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>

There were some #undef's of CONFIG_SYS_ARM_WITHOUT_RELOC added to a few board
configs as part of the arm relocation series; but these are not needed now as we
do not #undef what is not #defined in the first place.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Heiko Schocher <hs@denx.de>