Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Reworked the initial processor initialzation sequence:
* introduced cpu_early_init_f that is run in address space 1 (AS=1)
* Moved TLB/LAW and CCSR init into cpu_early_init_f()
* Reworked initial asm code to do most of the core init before TLBs

The main reasons for these changes are to allow handling of 36-bit phys
addresses in the future and some of the issues that will exist when we
do that.

There are a few caveats on what can be initialized via the LAW and TLB
static tables:
* TLB entry 14/15 can't be initialized via the TLB table
* any LAW that covers the implicit boot window (4G-8M to 4G) must map to
  the code that is currently executing.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add a set of functions to manipulate TLB entries:
 * set_tlb() - write a tlb entry
 * invalidate_tlb() - invalidate a tlb array
 * disable_tlb() - disable a variable size tlb entry
 * init_tlbs() - setup initial tlbs based on static table

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

We should be using the _MEM_PHYS for LAW and TLB setup and not _MEM_BASE.
While _MEM_BASE & _MEM_PHYS are normally the same, _MEM_BASE should only
be used for configuring the PCI ATMU.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

All boards are now using the new fsl_law code so we can drop the old version.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Converted ATUM8548, MPC8568 MDS, MPC8540 EVAL, and TQM85xx boards over
to use new LAW init code.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Move the initialization of the LAWs into C code and provide an API
to allow modification of LAWs after init.

Board code is responsible to provide a law_table and num_law_entries.

We should be able to use the same code on 86xx as well.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

MPC837xERDB board support includes:
* DDR2 330MHz hardcoded (soldered on the board)
* Local Bus NOR Flash
* I2C, UART and RTC
* eTSEC RGMII (TSEC0 - RTL8211B with MII;
*	       TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware
*		       load)

Signed-off-by: Kevin Lam <kevin.lam@freescale.com>
Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

System registers that are modified are the Arbiter Configuration
Register (ACR), the System Priority Control Register (SPCR), and the
System Clock Configuration Register (SCCR).

Signed-off by: Michael F. Reiss <Michael.F.Reiss@freescale.com>
Signed-off by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Before, the order of arguments to the pixis_reset
command needed to be supplied in a hard-coded order.
Generalize the command parsing to allow any order.

Signed-off-by: James Yang <james.yang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>

Convert the board/freescale/common/Makefile to use
CONFIG_* options to select which files to conditionally
compile into the board/freescale/common library rather
than conditionally compiling entire files.

Now handles::
    CONFIG_FSL_PIXIS
    CONFIG_FSL_DIU_FB
    CONFIG_PQ_MDS_PIB

CONFIG_ID_EEPROM is introduced until CFG_ID_EEPROM is gone.

Signed-off-by: Jon Loeliger <jdl@freescale.com>

Use driver/net/uli526x.c as MPC8610HPCD default Ethernet driver.
Remove unused ethernet CONFIG_ options.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>

continuation of commit b96c83d4

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

mpc8360emds.c: In function 'ft_board_setup':
mpc8360emds.c:327: warning: assignment makes pointer from integer without a cast
mpc8360emds.c:329: warning: passing argument 2 of 'fdt_getprop' makes integer from pointer without a cast
mpc8360emds.c:334: warning: passing argument 2 of 'fdt_setprop' makes integer from pointer without a cast
mpc8360emds.c:341: warning: assignment makes pointer from integer without a cast
mpc8360emds.c:343: warning: passing argument 2 of 'fdt_getprop' makes integer from pointer without a cast
mpc8360emds.c:348: warning: passing argument 2 of 'fdt_setprop' makes integer from pointer without a cast

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

use tree passed to us in local blob, not global fdt.

Also use fdt_path_offset to convert to relative offset, since absolute
reference is needed to check for rgmii-id mode string value.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

These changes were identified by HighSmith Bill ,Mazzyar and Joseph for
DDR configuration in u-boot code. Some are related to performance, some
affect stability and some correct few basic errors in the current
configuration.

The changes have been tested and found to give better memory latency
figures on MPC8313eRDB.LMBench figures prove it.

The changes are:

- CS0_CONFIG[ AP_n_EN] is changed from 1 to 0
  (this may improve performance for application with many read
  or write to open pages).
- CS0_CONFIG[ODT_WR_CFG] is currently changed from 100 to
  001 (activating all the CS when only one is used may cause
  unwanted noise on the system)

- TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 8clks (based on
  Tras=45ns)
- TIMING_CFG_1[REFREC] changed from 21 clks to 18clks.

- TIMING_CFG_2[AL] value changed from 0 setting to 1 clk to
  comply with the 3 ODT clk requirements)
- TIMING_CFG_2[CPO] was set to a reserved value, changed to RL+3/4.
- TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 6clks.

- DDR_SDRAM_MODE[AL]changed from 0 to 1.
- DDR_SDRAM_MODE[WRREC] changed from 1 clk to 3 clks.

- DDR_SDRAM_INTERVAL[REFINT] is changed from 0x0320 to 0x0510.
- DDR_SDRAM_INTERVAL[BSTOPRE] is changed from 0x64 to 0x0500.

The patch is based of git://www.denx.de/git/u-boot-mpc83xx.git


The last commit on this tree was 6775c686

Signed-off-by: Poonam Aggrwal-b10812 <b10812@freescale.com>
Cc: Bill HighSmith <Bill.Highsmith@freescale.com>
Cc: Razzaz Mazyar <MRazzaz@freescale.com>
Cc: Josep P J <PJ.Joseph@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

The isdram command prints out decoded information the "serial presence
detect" (SPD) chip on the SDRAM SIMMs.  This can be very helpful when
debugging memory configuration problems.

Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

The features list:
- Boot from NOR Flash
- DDR2 266MHz hardcoded configuration
- Local bus NOR Flash R/W operation
- I2C, UART, MII and RTC
- eTSEC0/1 support
- PCI host

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

The TSEC emergency priority definition of 831x/837x
is different than the definition of 834x in SPCR register.

Add the other config of TSEC emergency priority into
cpu_init.c

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

The MPC8360ERDK board support patch is added before
the commit 2c5b48fc
so, miss clean up it.

The patch clean up the miss cache config.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

OneNAND: Separate U-Boot dependent code from OneNAND

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>

adjust default environment;
disable SCC ethernet (not used on this board).

Signed-off-by: Wolfgang Denk <wd@denx.de>

qe.c: In function 'qe_upload_firmware':
qe.c:390: warning: pointer targets in passing argument 2
uec.c: In function 'uec_initialize':
uec.c:1236: warning: 'uec_info' may be used uninitialized

Signed-off-by: Dave Liu <daveliu@freescale.com>

Now that bit 29 is the USB PHY reset bit, update the Kilauea port
to remove the USB PHY reset after powerup. The CPLD will keep the
USB PHY in reset (active low) until the bit is set to 1 in
board_early_init_f().

Signed-off-by: Stefan Roese <sr@denx.de>

Signed-off-by: Wolfgang Denk <wd@denx.de>