SMDKV310 board is based on Samsung S5PV310 SOC. This SOC is very much
similar to S5PC210.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

Signed-off-by: David Müller <d.mueller@elsoft.ch>

commit ed59e587 (Remove device tree booting dependency on CONFIG_SYS_BOOTMAPSZ) made the
definition of CONFIG_SYS_BOOTMAPSZ unnecessary.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <jason.hui@linaro.org>

config.mk should not be used in board directory and should be removed.
Use the same approach for building the image as other MX51/MX53 boards.

After this change vision2 board can be built again.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

This patch add initial support for freescale MX53LOCO board.
Network(FEC),SD/MMC,UART have been supported by this patch

Signed-off-by: Jason Liu <jason.hui@linaro.org>

With the following commit, CONFIG_OF_LIBFDT is redefined.

  2fa8ca98
  Add CONFIG_OF_LIBFDT to more boards.

Remove the duplicated definition to fix CONFIG_OF_LIBFDT redefined
warning.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Since the following commit, definition CONFIG_SYS_BOOTMAPSZ is not
needed any more.

  ed59e587
  Remove device tree booting dependency on CONFIG_SYS_BOOTMAPSZ

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

No need to use '#define SYMBOL 1' to make it active.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>

The pnvram size was used later from start scripts in linux. Therefore
it was added to the default environment.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>

This is a first step to simplify the default environment. Move all
the environment variables which are only needed for debugging
purpose to textfiles in the scripts directory. In case of debugging
these files can be loaded via tftp into RAM and set via the env import
command. Other variables are identified as obsolete and were removed.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>

BoardId and HWKey are used to identify the HW class of a given board.
The correct values are stored in the inventory eeprom. During creation
time of a boot package the boardId and HWkey for the SW is stored in
the default environment and burned into the flash. During boottime
the values in the inventory and in the environment are compared to
avoid starting of a SW which is not authorized for this board.

Some bootpackages are allowed to run on a set of different boardId
hwKey. In this case the environment variable boardIdListHex was added
to the default environment. In this case the command iterates over the
pair values and compares them with the values read from the inventory
eeprom.

The syntax of such a boardIdListHex value is e.g.: 158_1 159_1 159_2

Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>

For emmc, it may have up to 7 partitions: two boot partitions, one
user partition, one RPMB partition and four general purpose partitions.
(Refer to JESD84-A44.pdf/page 154)

As bootloader may need to read out or reflashing images on those

different partitions, it is better to enable the partition switch with
console command support.

Also for partition would be restore to user partition(part 0) when CMD0
is used, so change mmc_init routine to perform normal initialization
only once for each slot, unless use the rescan command to force init
again.

Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>

mmc command applied device, like ide and usb...

Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>

A "send status" command is added with the commit "mmc: checking
status after commands with R1b response". But the status register
returned from send status command of SPI protocol is different from
that of MMC/SD protocol. We do a simple test and generate a response
in stead of full bit-by-bit translation.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>

Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The otc570 board support was broken. Within this opportunity, I completely
reworked the board files.

Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>