AX88180: switch to common mii.h header

No compiled code change here, just drop the local PHY defines in favor of
the common standard ones.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

drivers/net/ax88180.c

@@ -41,6 +41,7 @@
 #include <command.h>
 #include <net.h>
 #include <malloc.h>
+#include <linux/mii.h>
 #include "ax88180.h"
 
 /*
@@ -112,10 +113,10 @@ static int ax88180_phy_reset (struct eth_device *dev)
 {
 	unsigned short delay_cnt = 500;
 
-	ax88180_mdio_write (dev, BMCR, (PHY_RESET | AUTONEG_EN));
+	ax88180_mdio_write (dev, MII_BMCR, (BMCR_RESET | BMCR_ANENABLE));
 
 	/* Wait for the reset to complete, or time out (500 ms) */
-	while (ax88180_mdio_read (dev, BMCR) & PHY_RESET) {
+	while (ax88180_mdio_read (dev, MII_BMCR) & BMCR_RESET) {
 		udelay (1000);
 		if (--delay_cnt == 0) {
 			printf ("Failed to reset PHY!\n");
@@ -265,10 +266,10 @@ static int ax88180_phy_initial (struct eth_device *dev)
 #endif
 	{
 		priv->PhyAddr = phyaddr;
-		priv->PhyID0 = ax88180_mdio_read(dev, PHYIDR0);
+		priv->PhyID0 = ax88180_mdio_read(dev, MII_PHYSID1);
 
 		switch (priv->PhyID0) {
-		case MARVELL_88E1111_PHYIDR0:
+		case MARVELL_88E1111_PHYSID0:
 			debug("ax88180: Found Marvell 88E1111 PHY."
 			      " (PHY Addr=0x%x)\n", priv->PhyAddr);
 
@@ -282,7 +283,7 @@ static int ax88180_phy_initial (struct eth_device *dev)
 
 			return 1;
 
-		case CICADA_CIS8201_PHYIDR0:
+		case CICADA_CIS8201_PHYSID0:
 			debug("ax88180: Found CICADA CIS8201 PHY"
 			      " chipset. (PHY Addr=0x%x)\n", priv->PhyAddr);
 
@@ -321,20 +322,20 @@ static void ax88180_media_config (struct eth_device *dev)
 
 	/* Waiting 2 seconds for PHY link stable */
 	for (i = 0; i < 20000; i++) {
-		bmsr_val = ax88180_mdio_read (dev, BMSR);
-		if (bmsr_val & LINKOK) {
+		bmsr_val = ax88180_mdio_read (dev, MII_BMSR);
+		if (bmsr_val & BMSR_LSTATUS) {
 			break;
 		}
 		udelay (100);
 	}
 
-	bmsr_val = ax88180_mdio_read (dev, BMSR);
+	bmsr_val = ax88180_mdio_read (dev, MII_BMSR);
 	debug ("ax88180: BMSR=0x%04x\n", (unsigned int)bmsr_val);
 
-	if (bmsr_val & LINKOK) {
-		bmcr_val = ax88180_mdio_read (dev, BMCR);
+	if (bmsr_val & BMSR_LSTATUS) {
+		bmcr_val = ax88180_mdio_read (dev, MII_BMCR);
 
-		if (bmcr_val & AUTONEG_EN) {
+		if (bmcr_val & BMCR_ANENABLE) {
 
 			/*
 			 * Waiting for Auto-negotiation completion, this may
@@ -343,8 +344,8 @@ static void ax88180_media_config (struct eth_device *dev)
 			debug ("ax88180: Auto-negotiation is "
 			       "enabled. Waiting for NWay completion..\n");
 			for (i = 0; i < 50000; i++) {
-				bmsr_val = ax88180_mdio_read (dev, BMSR);
-				if (bmsr_val & AUTONEG_COMPLETE) {
+				bmsr_val = ax88180_mdio_read (dev, MII_BMSR);
+				if (bmsr_val & BMSR_ANEGCOMPLETE) {
 					break;
 				}
 				udelay (100);
@@ -357,10 +358,10 @@ static void ax88180_media_config (struct eth_device *dev)
 
 		/* Get real media mode here */
 		switch (priv->PhyID0) {
-		case MARVELL_88E1111_PHYIDR0:
+		case MARVELL_88E1111_PHYSID0:
 			RealMediaMode = get_MarvellPHY_media_mode(dev);
 			break;
-		case CICADA_CIS8201_PHYIDR0:
+		case CICADA_CIS8201_PHYSID0:
 			RealMediaMode = get_CicadaPHY_media_mode(dev);
 			break;
 		default:

drivers/net/ax88180.h

@@ -63,9 +63,9 @@ struct ax88180_private {
 /* Max Rx Jumbo size is 15K Bytes */
 #define MAX_RX_SIZE			0x3C00
 
-#define MARVELL_88E1111_PHYIDR0	0x0141
+#define MARVELL_88E1111_PHYSID0	0x0141
 
-#define CICADA_CIS8201_PHYIDR0		0x000F
+#define CICADA_CIS8201_PHYSID0		0x000F
 
 #define MEDIA_AUTO			0
 #define MEDIA_1000FULL			1
@@ -276,50 +276,6 @@ struct ax88180_private {
   #define SOFTRST_NORMAL	0x00000003
   #define SOFTRST_RESET_MAC	0x00000002
 
-/* External PHY Register Definition */
-#define BMCR		0x0000
-  #define LINE_SPEED_MSB	0x0040
-  #define DUPLEX_MODE		0x0100
-  #define RESTART_AUTONEG	0x0200
-  #define POWER_DOWN		0x0800
-  #define AUTONEG_EN		0x1000
-  #define LINE_SPEED_LSB	0x2000
-  #define PHY_RESET		0x8000
-
-  #define MEDIAMODE_MASK	(LINE_SPEED_MSB | LINE_SPEED_LSB |\
-				 DUPLEX_MODE)
-  #define BMCR_SPEED_1000	LINE_SPEED_MSB
-  #define BMCR_SPEED_100	LINE_SPEED_LSB
-  #define BMCR_SPEED_10	0x0000
-
-  #define BMCR_1000FULL	(BMCR_SPEED_1000 | DUPLEX_MODE)
-  #define BMCR_100FULL		(BMCR_SPEED_100 | DUPLEX_MODE)
-  #define BMCR_100HALF		BMCR_SPEED_100
-  #define BMCR_10FULL		DUPLEX_MODE
-  #define BMCR_10HALF		0x0000
-#define BMSR		0x0001
-  #define LINKOK		0x0004
-  #define AUTONEG_ENABLE_STS	0x0008
-  #define AUTONEG_COMPLETE	0x0020
-#define PHYIDR0		0x0002
-#define PHYIDR1		0x0003
-#define ANAR		0x0004
-  #define ANAR_PAUSE		0x0400
-  #define ANAR_100FULL		0x0100
-  #define ANAR_100HALF		0x0080
-  #define ANAR_10FULL		0x0040
-  #define ANAR_10HALF		0x0020
-  #define ANAR_8023BIT		0x0001
-#define ANLPAR		0x0005
-#define ANER		0x0006
-#define AUX_1000_CTRL	0x0009
-  #define ENABLE_1000HALF	0x0100
-  #define ENABLE_1000FULL	0x0200
-  #define DEFAULT_AUX_1000_CTRL	(ENABLE_1000HALF | ENABLE_1000FULL)
-#define AUX_1000_STATUS	0x000A
-  #define LP_1000HALF		0x0400
-  #define LP_1000FULL		0x0800
-
 /* Marvell 88E1111 Gigabit PHY Register Definition */
 #define M88_SSR		0x0011
   #define SSR_SPEED_MASK	0xC000