diff --git a/MAINTAINERS b/MAINTAINERS
index ee4e8d5bcfb0a79fd9be5c11cfe5d4d1f701a042..143f31bbcfcab67355eb0f9e4ac5d445ffc21325 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -517,6 +517,7 @@ Ilya Yanok <yanok@emcraft.com>
 Roy Zang <tie-fei.zang@freescale.com>
 
 	mpc7448hpc2	MPC7448
+	P1023RDS	P1023
 
 John Zhan <zhanz@sinovee.com>
 
diff --git a/board/freescale/p1023rds/Makefile b/board/freescale/p1023rds/Makefile
new file mode 100644
index 0000000000000000000000000000000000000000..bf8758044099420e2d582a4f43274ee51b983e6b
--- /dev/null
+++ b/board/freescale/p1023rds/Makefile
@@ -0,0 +1,38 @@
+#
+# Copyright 2010-2011 Freescale Semiconductor, Inc.
+#
+# This program is free software; you can redistribute it and/or modify it
+# under the terms of the GNU General Public License as published by the Free
+# Software Foundation; either version 2 of the License, or (at your option)
+# any later version.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).o
+
+COBJS-y	+= $(BOARD).o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/p1023rds/bcsr.h b/board/freescale/p1023rds/bcsr.h
new file mode 100644
index 0000000000000000000000000000000000000000..0995aa47d0f04546c0c794aa471a2f972884900d
--- /dev/null
+++ b/board/freescale/p1023rds/bcsr.h
@@ -0,0 +1,53 @@
+/*
+ * Copyright (C) 2011 Freescale Semiconductor, Inc.
+ *
+ * Authors:  Chunhe Lan <b25806@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation; either version 2 of the License, or (at your option)
+ * any later version.
+ *
+ */
+
+#ifndef __BCSR_H_
+#define __BCSR_H_
+
+#include <common.h>
+
+/*
+ * BCSR Bit definitions
+	* BCSR 15 *
+	0	device insertion oriention
+	1	stack processor present
+	2	power supply shut down/normal operation
+	3	I2C bus0 drive enable
+	4	reserved
+	5:7	I2C bus0 select
+				5 - I2C_BUS_0_SS0
+				6 - I2C_BUS_0_SS1
+				7 - I2C_BUS_0_SS2
+*/
+
+/* BCSR register base address is 0xFX000020 */
+#define BCSR_BASE_REG_OFFSET	0x20
+#define BCSR_ACCESS_REG_ADDR	(CONFIG_SYS_BCSR_BASE + BCSR_BASE_REG_OFFSET)
+
+#define BCSR15_DEV_INS_ORI	0x80
+#define BCSR15_STACK_PRO_PRE	0x40
+#define BCSR15_POWER_SUPPLY	0x20
+#define BCSR15_I2C_BUS0_EN	0x10
+#define BCSR15_I2C_BUS0_SEG0	0x00
+#define BCSR15_I2C_BUS0_SEG1	0x04
+#define BCSR15_I2C_BUS0_SEG2	0x02
+#define BCSR15_I2C_BUS0_SEG3	0x06
+#define BCSR15_I2C_BUS0_SEG4	0x01
+#define BCSR15_I2C_BUS0_SEG5	0x05
+#define BCSR15_I2C_BUS0_SEG6	0x03
+#define BCSR15_I2C_BUS0_SEG7	0x07
+#define BCSR15_I2C_BUS0_SEG_CLR	0x07
+#define BCSR19_SGMII_SEL_L	0x01
+
+/*BCSR Utils functions*/
+void fixup_i2c_bus0_sel_seg0(void);
+#endif  /* __BCSR_H_ */
diff --git a/board/freescale/p1023rds/law.c b/board/freescale/p1023rds/law.c
new file mode 100644
index 0000000000000000000000000000000000000000..f140f64dda67ef1f4ff326166bf2a4eb72c3bb77
--- /dev/null
+++ b/board/freescale/p1023rds/law.c
@@ -0,0 +1,35 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
+	SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_4M,
+					LAW_TRGT_IF_DPAA_SWP_SRAM),
+	/* The LAW 0xe0000000 ~ 0xefffffff for BCSR and NOR flash */
+	SET_LAW(CONFIG_SYS_BCSR_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/p1023rds/p1023rds.c b/board/freescale/p1023rds/p1023rds.c
new file mode 100644
index 0000000000000000000000000000000000000000..8cfd199d6572d843520c8f3b7da770201639b665
--- /dev/null
+++ b/board/freescale/p1023rds/p1023rds.c
@@ -0,0 +1,162 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * Authors:  Roy Zang <tie-fei.zang@freescale.com>
+ *           Chunhe Lan <b25806@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/io.h>
+#include <asm/cache.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_pci.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_portals.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <netdev.h>
+#include <malloc.h>
+
+#include "bcsr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+	fsl_lbc_t *lbc = LBC_BASE_ADDR;
+
+	/* Set ABSWP to implement conversion of addresses in the LBC */
+	setbits_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	u8 *bcsr = (u8 *)BCSR_ACCESS_REG_ADDR;
+
+	printf("Board: P1023 RDS\n");
+
+	clrbits_8(&bcsr[15], BCSR15_I2C_BUS0_SEG_CLR);
+	setbits_8(&bcsr[15], BCSR15_I2C_BUS0_SEG0);
+
+	return 0;
+}
+
+/* Fixed sdram init -- doesn't use serial presence detect. */
+phys_size_t fixed_sdram(void)
+{
+#ifndef CONFIG_SYS_RAMBOOT
+	ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR;
+
+	set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1);
+
+	out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS);
+	out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG);
+	out_be32(&ddr->cs1_bnds, CONFIG_SYS_DDR_CS1_BNDS);
+	out_be32(&ddr->cs1_config, CONFIG_SYS_DDR_CS1_CONFIG);
+	out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+	out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+	out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+	out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+	out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL2);
+	out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1);
+	out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2);
+	out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+	out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT);
+	out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL);
+	out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4);
+	out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5);
+	out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CNTL);
+	out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL);
+	out_be32(&ddr->ddr_cdr1, CONFIG_SYS_DDR_CDR_1);
+	out_be32(&ddr->ddr_cdr2, CONFIG_SYS_DDR_CDR_2);
+	out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
+#endif
+	return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024ul;
+}
+
+#ifdef CONFIG_PCI
+void pci_init_board(void)
+{
+	fsl_pcie_init_board(0);
+}
+#endif
+
+int board_early_init_r(void)
+{
+	const unsigned int flashbase = CONFIG_SYS_BCSR_BASE;
+	const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+	/*
+	 * Remap Boot flash + BCSR region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Flush d-cache and invalidate i-cache of any FLASH data */
+	flush_dcache();
+	invalidate_icache();
+
+	/* invalidate existing TLB entry for flash + bcsr */
+	disable_tlb(flash_esel);
+
+	set_tlb(1, flashbase, CONFIG_SYS_BCSR_BASE_PHYS,
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+			0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+	setup_portals();
+
+	return 0;
+}
+
+unsigned long get_board_sys_clk(ulong dummy)
+{
+	return gd->bus_clk;
+}
+
+unsigned long get_board_ddr_clk(ulong dummy)
+{
+	return gd->mem_clk;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	return pci_eth_init(bis);
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	phys_addr_t base;
+	phys_size_t size;
+
+	ft_cpu_setup(blob, bd);
+
+	base = getenv_bootm_low();
+	size = getenv_bootm_size();
+
+	fdt_fixup_memory(blob, (u64)base, (u64)size);
+}
+#endif
diff --git a/board/freescale/p1023rds/tlb.c b/board/freescale/p1023rds/tlb.c
new file mode 100644
index 0000000000000000000000000000000000000000..2b3b67900fb614017e31cb6fb430fa0744f1c542
--- /dev/null
+++ b/board/freescale/p1023rds/tlb.c
@@ -0,0 +1,118 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+	/* *I*** - Covers boot page */
+	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I,
+		      0, 0, BOOKE_PAGESZ_4K, 1),
+
+	/* *I*G* - CCSRBAR */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 1, BOOKE_PAGESZ_4M, 1),
+
+#ifndef CONFIG_NAND_SPL
+	/* *W*G* - BCSR and NOR flash on local bus*/
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CONFIG_SYS_BCSR_BASE, CONFIG_SYS_BCSR_BASE_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
+		      0, 2, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 3, BOOKE_PAGESZ_1G, 1),
+
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x40000000,
+		      CONFIG_SYS_PCIE3_MEM_PHYS + 0x40000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 4, BOOKE_PAGESZ_256M, 1),
+
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT + 0x50000000,
+		      CONFIG_SYS_PCIE3_MEM_PHYS + 0x50000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 5, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - PCI I/O */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_IO_VIRT, CONFIG_SYS_PCIE3_IO_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 6, BOOKE_PAGESZ_256K, 1),
+
+	/* Bman/Qman */
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 7, BOOKE_PAGESZ_1M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000,
+		      CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 8, BOOKE_PAGESZ_1M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
+		      0, 9, BOOKE_PAGESZ_1M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000,
+		      CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 10, BOOKE_PAGESZ_1M, 1),
+#endif
+
+	/* *I*G - NAND */
+	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 11, BOOKE_PAGESZ_1M, 1),
+
+#ifdef CONFIG_SYS_RAMBOOT
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE,
+		      CONFIG_SYS_DDR_SDRAM_BASE,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 12, BOOKE_PAGESZ_1G, 1),
+
+	SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+		      CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 13, BOOKE_PAGESZ_1G, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index c1623f320fd91d19ef98b2e82eeeb84fc84279f5..4522ea7a0909e3aa033865c5e060fbf09ae28ca2 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -576,6 +576,8 @@ P1020RDB_SDCARD              powerpc     mpc85xx     p1_p2_rdb           freesca
 P1020RDB_SPIFLASH            powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P1020RDB,SPIFLASH
 P1022DS                      powerpc     mpc85xx     p1022ds             freescale
 P1022DS_36BIT                powerpc     mpc85xx     p1022ds             freescale      -           P1022DS:36BIT
+P1023RDS                     powerpc     mpc85xx     p1023rds            freescale      -           P1023RDS
+P1023RDS_NAND                powerpc     mpc85xx     p1023rds            freescale      -           P1023RDS:NAND
 P2010RDB                     powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P2010RDB
 P2010RDB_36BIT               powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P2010RDB,36BIT
 P2010RDB_36BIT_SDCARD        powerpc     mpc85xx     p1_p2_rdb           freescale      -           P1_P2_RDB:P2010RDB,36BIT,SDCARD
diff --git a/doc/README.p1023rds b/doc/README.p1023rds
new file mode 100644
index 0000000000000000000000000000000000000000..685f5daa995c7e11161edeff58816a12e1762cbf
--- /dev/null
+++ b/doc/README.p1023rds
@@ -0,0 +1,101 @@
+Overview
+--------
+The P1023 process includes a performance optimized implementation of the
+QorIQ data Path Acceleration Architecture (DPAA).  This architecture
+provides the infrastructure to support simplified sharing of networking
+interfaces and accelerators by multiple CPU cores. P1023 is an e500 based
+dual core SOC.
+
+P1023RDS board is a Low End Dual core platform supporting the P1023
+processor of QorIQ series.
+
+Building U-boot
+---------------
+To build the u-boot for P1023RDS:
+Configure to NOR boot:
+	make P1023RDS_config
+Configure to NAND boot:
+	make P1023RDS_NAND_config
+Build:
+	make
+
+Board Switches
+--------------
+Most switches on the board should not be changed.  The most frequent
+user-settable switches on the board are used to configure
+the flash banks.
+
+J4: all open
+
+Default NOR flash boot switch setting:
+ Sw3[1:8]: off on on off on on off off
+ Sw4[1:8]: off off off on off off off off
+ Sw6[1:8]: off on off on off on on off
+ Sw7[1:8]: off on off off on off off off
+ Sw8[1:8]: on off off off off off off off
+
+For NAND flash boot,set
+Sw4[1:4]: off on on on
+
+The default native ethernet setting is for RGMII mode.
+To use SGMII mode, set
+SW8[1:2]: OFF OFF
+SW7[6:7]: ON ON
+
+Memory Map
+----------
+0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
+0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
+0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
+0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
+
+0xe000_0000	0xe003_ffff	BCSR			256K BCSR
+0xee00_0000	0xefff_ffff	NOR flash		32M NOR flash
+0xff00_0000	0xff3f_ffff	DPAA_QBMAN		4M
+0xff60_0000	0xff7f_ffff	CCSR			2M non-cacheable
+0xffa0_0000	0xffaf_ffff	NAND FLASH		1M non-cacheable
+0xffd0_0000	0xffd0_3fff	L1 for stack		16K Cacheable TLB0
+
+Flashing u-boot Images
+---------------
+To program the image in the boot flash bank:
+NOR flash boot:
+	=> tftp 1000000 u-boot.bin
+	=> protect off all
+	=> erase eff80000 efffffff
+	=> cp.b 1000000 eff80000 80000
+
+NAND flash boot:
+	=> tftp 1000000 u-boot-nand.bin
+	=> nand erase 0 80000
+	=> nand write 1000000 0 80000
+
+Firmware ucode location
+---------------------------------
+Microcode(ucode) to FMAN's IRAM is needed to make FMAN Ethernet work.
+u-boot loads ucode FLASH. The location for ucode:
+NOR Flash: 0xfe000000
+NAND Flash: 0x1f00000
+
+Using the Device Tree Source File
+---------------------------------
+To create the DTB (Device Tree Binary) image file,
+use a command similar to this:
+
+	dtc -b 0 -f -I dts -O dtb p1023rds.dts > p1023rds.dtb
+
+Likely, that .dts file will come from here;
+
+	linux-2.6/arch/powerpc/boot/dts/p1023rds.dts
+or
+	make p1023rds.dtb ARCH=powerpc
+in linux-2.6 directory.
+
+Booting Linux
+-------------
+Place a linux uImage in the TFTP disk area.
+
+	tftp 1000000 uImage
+	tftp 2000000 rootfs.ext2.gz.uboot
+	tftp c00000 p1023rds.dtb
+	bootm 1000000 2000000 c00000
diff --git a/include/configs/P1023RDS.h b/include/configs/P1023RDS.h
new file mode 100644
index 0000000000000000000000000000000000000000..4f14a02a305e3aa5ae494e07567a0cbcee7ceb9b
--- /dev/null
+++ b/include/configs/P1023RDS.h
@@ -0,0 +1,562 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ *
+ * Authors:  Roy Zang <tie-fei.zang@freescale.com>
+ *	     Chunhe Lan <b25806@freescale.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * p1023rds board configuration file
+ *
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#ifdef CONFIG_NAND
+#define CONFIG_NAND_U_BOOT
+#define CONFIG_RAMBOOT_NAND
+#endif
+
+#ifdef CONFIG_NAND_U_BOOT
+#define CONFIG_SYS_TEXT_BASE_SPL	0xfff00000
+#define CONFIG_SYS_TEXT_BASE		0x11001000
+
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
+#else
+#define CONFIG_SYS_LDSCRIPT $(TOPDIR)/$(CPUDIR)/u-boot-nand.lds
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+#endif /* CONFIG_NAND_SPL */
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE	0xeff80000
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		/* BOOKE */
+#define CONFIG_E500		/* BOOKE e500 family */
+#define CONFIG_MPC85xx
+#define CONFIG_P1023
+#define CONFIG_P1023RDS
+#define CONFIG_MP		/* support multiple processors */
+
+#define CONFIG_FSL_ELBC		/* Has Enhanced localbus controller */
+#define CONFIG_PCI		/* Enable PCI/PCIE */
+#define CONFIG_PCIE1		/* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE2		/* PCIE controler 2 (slot 2) */
+#define CONFIG_PCIE3		/* PCIE controler 3 (slot 3) */
+#define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
+#define CONFIG_FSL_PCIE_RESET	/* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
+#define CONFIG_FSL_LAW		/* Use common FSL init code */
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_clock_freq(void);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ	66666666
+#define CONFIG_DDR_CLK_FREQ	CONFIG_SYS_CLK_FREQ
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE			/* toggle L2 cache */
+#define CONFIG_BTB			/* toggle branch predition */
+#define CONFIG_HWCONFIG
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x1fffffff	/* fix me, only 1G */
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+#define CONFIG_SYS_LBC_LBCR	0x00000000	/* Implement conversion of
+						addresses in the LBC */
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xff600000	/* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR		0xff600000	/* relocated CCSRBAR */
+/* physical addr of CCSRBAR */
+#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR
+#define CONFIG_SYS_IMMR	CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+
+/* DDR Setup */
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	2
+
+/* These are used when DDR doesn't use SPD.  */
+#define CONFIG_SYS_SDRAM_SIZE		2048u	/* DDR is 2GB */
+
+/* Default settings for "stable" mode */
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000003F
+#define CONFIG_SYS_DDR_CS1_BNDS		0x0040007F
+#define CONFIG_SYS_DDR_CS0_CONFIG	0x80014302
+#define CONFIG_SYS_DDR_CS1_CONFIG	0x80014302
+#define CONFIG_SYS_DDR_TIMING_3		0x00020000
+#define CONFIG_SYS_DDR_TIMING_0		0x40110104
+#define CONFIG_SYS_DDR_TIMING_1		0x5C59E544
+#define CONFIG_SYS_DDR_TIMING_2		0x0fA888CA
+#define CONFIG_SYS_DDR_MODE_1		0x00441210
+#define CONFIG_SYS_DDR_MODE_2		0x00000000
+#define CONFIG_SYS_DDR_MODE_CTRL	0x00000000
+#define CONFIG_SYS_DDR_INTERVAL		0x0A280100
+#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
+#define CONFIG_SYS_DDR_CLK_CTRL		0x01800000
+#define CONFIG_SYS_DDR_TIMING_4		0x00000001
+#define CONFIG_SYS_DDR_TIMING_5		0x01401400
+#define CONFIG_SYS_DDR_ZQ_CNTL		0x89080600
+#define CONFIG_SYS_DDR_WRLVL_CNTL	0x8675F605
+#define CONFIG_SYS_DDR_CONTROL	0xC70C0008 /* Type = DDR3: No Interleaving */
+#define CONFIG_SYS_DDR_CONTROL2		0x24401010
+#define CONFIG_SYS_DDR_CDR1		0x00000000
+#define CONFIG_SYS_DDR_CDR2		0x00000000
+
+#define CONFIG_SYS_DDR_ERR_INT_EN	0x00000000
+#define CONFIG_SYS_DDR_ERR_DIS		0x00000000
+#define CONFIG_SYS_DDR_SBE		0x00000000
+
+/* Settings that differ for "performance" mode */
+#define CONFIG_SYS_DDR_CS0_BNDS_PERF	0x0000007F /* Interleaving Enabled */
+#define CONFIG_SYS_DDR_CS1_BNDS_PERF	0x00000000 /* Interleaving Enabled */
+#define CONFIG_SYS_DDR_CS1_CONFIG_PERF	0x80014302
+#define CONFIG_SYS_DDR_TIMING_1_PERF	0x5C58E544
+#define CONFIG_SYS_DDR_TIMING_2_PERF	0x0FA888CA
+/* Type = DDR3: cs0-cs1 interleaving */
+#define CONFIG_SYS_DDR_CONTROL_PERF	0xC70C4008
+#define CONFIG_SYS_DDR_CDR_1		0x00000000
+#define CONFIG_SYS_DDR_CDR_2		0x00000000
+
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
+ * 0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
+ * 0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
+ * 0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
+ *
+ * Localbus non-cacheable
+ * 0xe000_0000	0xe003_ffff	BCSR			256K BCSR
+ * 0xee00_0000	0xefff_ffff	NOR flash		32M NOR flash
+ * 0xff00_0000	0xff3f_ffff	DPAA_QBMAN		4M
+ * 0xff60_0000	0xff7f_ffff	CCSR			2M non-cacheable
+ * 0xffa0_0000	0xffaf_ffff	NAND			1M non-cacheable
+ * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K Cacheable TLB0
+ */
+
+/*
+ * Local Bus Definitions
+ */
+#define CONFIG_SYS_BCSR_BASE		0xe0000000 /* start of on board FPGA */
+#define CONFIG_SYS_BCSR_BASE_PHYS	CONFIG_SYS_BCSR_BASE
+
+#ifndef CONFIG_NAND
+#define CONFIG_SYS_FLASH_BASE		0xee000000 /* start of FLASH 32M */
+
+#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_FLASH_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
+		| BR_PS_16 | BR_V)
+#define CONFIG_FLASH_OR_PRELIM	0xfe000ff7
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	512	/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+#else
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#if defined(CONFIG_SYS_SPL) || defined(CONFIG_RAMBOOT_NAND)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_F	/* call board_early_init_f function */
+#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
+
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_END	0x00004000	/* End of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_SIZE	128	/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	\
+	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN	(256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN	(6 * 1024 * 1024) /* Reserved for malloc */
+
+#ifndef CONFIG_NAND_SPL
+#define CONFIG_SYS_NAND_BASE		0xffa00000
+#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
+#else
+#define CONFIG_SYS_NAND_BASE		0xfff00000
+#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
+#endif
+
+#define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE}
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+#define CONFIG_NAND_FSL_ELBC
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(16 * 1024)
+
+/* NAND boot: 4K NAND loader config */
+#define CONFIG_SYS_NAND_SPL_SIZE	0x1000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	((512 << 10) + CONFIG_SYS_NAND_SPL_SIZE)
+#define CONFIG_SYS_NAND_U_BOOT_DST	(0x11000000 - CONFIG_SYS_NAND_SPL_SIZE)
+#define CONFIG_SYS_NAND_U_BOOT_START	0x11000000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	(0)
+#define CONFIG_SYS_NAND_U_BOOT_RELOC	0x00010000
+#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP	(CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000)
+
+/* NAND flash config */
+#define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
+				| BR_PS_8		/* Port Size = 8bit */ \
+				| BR_MS_FCM		/* MSEL = FCM */ \
+				| BR_V)			/* valid */
+#define CONFIG_SYS_NAND_OR_PRELIM  (0xFFF80000		/* length 32K */ \
+				| OR_FCM_CSCT \
+				| OR_FCM_CST \
+				| OR_FCM_CHT \
+				| OR_FCM_SCY_1 \
+				| OR_FCM_TRLX \
+				| OR_FCM_EHTR)
+
+#ifdef CONFIG_RAMBOOT_NAND
+/* NAND Base Address */
+#define CONFIG_SYS_BR0_PRELIM	CONFIG_SYS_NAND_BR_PRELIM
+#define CONFIG_SYS_OR0_PRELIM	CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
+/* chip select 1 - BCSR */
+#define CONFIG_SYS_BR1_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \
+				| BR_MS_GPCM | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR1_PRELIM  (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \
+				| OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \
+				| OR_GPCM_EAD)
+#else
+#define CONFIG_SYS_BR0_PRELIM  CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
+#define CONFIG_SYS_OR0_PRELIM  CONFIG_FLASH_OR_PRELIM	/* NOR Options */
+/* chip select 1 - BCSR */
+#define CONFIG_SYS_BR1_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_BCSR_BASE_PHYS) \
+				| BR_MS_GPCM | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR1_PRELIM  (OR_AM_32KB | OR_GPCM_CSNT | OR_GPCM_XACS \
+				| OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR \
+				| OR_GPCM_EAD)
+#endif
+
+/* Serial Port
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX		1
+#undef	CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_NS16550_MIN_FUNCTIONS
+#endif
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR + 0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef	CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+#define CONFIG_SYS_64BIT_VSPRINTF
+#define CONFIG_SYS_64BIT_STRTOUL
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#undef	CONFIG_SOFT_I2C		/* I2C bit-banged */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x51
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_I2C2_OFFSET		0x3100
+
+/*
+ * I2C2 EEPROM
+ */
+#define CONFIG_ID_EEPROM
+#ifdef CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#endif
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x51
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+#define CONFIG_SYS_EEPROM_BUS_NUM	0
+
+#define CONFIG_CMD_I2C
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ATMEL
+
+#define CONFIG_HARD_SPI
+#define CONFIG_FSL_ESPI
+
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED		10000000
+#define CONFIG_SF_DEFAULT_MODE		0
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 3, Slot 1, tgtid 3, Base address b000 */
+#define CONFIG_SYS_PCIE3_NAME		"Slot 3"
+#define CONFIG_SYS_PCIE3_MEM_VIRT	0x80000000
+#define CONFIG_SYS_PCIE3_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	0x80000000
+#define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE3_IO_VIRT	0xffc00000
+#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS	0xffc00000
+#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 2, direct to uli, tgtid 2, Base address 9000 */
+#define CONFIG_SYS_PCIE2_NAME		"Slot 2"
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 1, Slot 2, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME		"Slot 1"
+#define CONFIG_SYS_PCIE1_MEM_VIRT	0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc0000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc20000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xffc20000
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+
+#if defined(CONFIG_PCI)
+#define CONFIG_E1000		/* Defind e1000 pci Ethernet card */
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
+#endif	/* CONFIG_PCI */
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_SYS_RAMBOOT)
+#if defined(CONFIG_RAMBOOT_NAND)
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET	((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_ENV_IS_NOWHERE	/* Store ENV in memory only */
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x4000)
+#define CONFIG_ENV_SIZE		0x2000
+#endif
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
+#define CONFIG_ENV_ADDR		0xfff80000
+#else
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#endif
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+#endif
+
+#define CONFIG_LOADS_ECHO		/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+
+#if defined(CONFIG_PCI)
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * USB
+ */
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_USB_STORAGE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HZ	1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 16 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(16 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(16 << 20) /* Increase max gunzip size */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_BOOTFILE		uImage
+#define CONFIG_UBOOTPATH	(u-boot.bin) /* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
+
+#define CONFIG_BAUDRATE	115200
+
+/* Qman/Bman */
+#define CONFIG_SYS_DPAA_QBMAN		/* support Q/Bman */
+#define CONFIG_SYS_QMAN_MEM_BASE	0xff000000
+#define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
+#define CONFIG_SYS_QMAN_MEM_SIZE	0x00200000
+#define CONFIG_SYS_BMAN_MEM_BASE	0xff200000
+#define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
+#define CONFIG_SYS_BMAN_MEM_SIZE	0x00200000
+
+/* For FM */
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#endif
+
+#ifndef CONFIG_NAND
+/* Default address of microcode for the Linux Fman driver */
+/* QE microcode/firmware address */
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEF000000
+#define CONFIG_SYS_FMAN_FW_ADDR_PHYS	CONFIG_SYS_FMAN_FW_ADDR
+#else
+#define CONFIG_SYS_QE_FW_IN_NAND	0x1f00000
+#define CONFIG_SYS_FMAN_FW_ADDR		0x10000000
+#define CONFIG_SYS_FMAN_FW_LENGTH	0x10000
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR	0x2
+#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR	0x7
+
+#define CONFIG_SYS_TBIPA_VALUE	8
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_ETHPRIME		"FM1@DTSEC1"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS	\
+	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"
+
+#endif	/* __CONFIG_H */
diff --git a/nand_spl/board/freescale/p1023rds/Makefile b/nand_spl/board/freescale/p1023rds/Makefile
new file mode 100644
index 0000000000000000000000000000000000000000..168e8686413113297e2c3e572a2fd8fb74dd00a8
--- /dev/null
+++ b/nand_spl/board/freescale/p1023rds/Makefile
@@ -0,0 +1,132 @@
+#
+# Copyright 2010-2011 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+NAND_SPL := y
+PAD_TO := 0xfff01000
+
+include $(TOPDIR)/config.mk
+
+nandobj	:= $(OBJTREE)/nand_spl/
+
+LDSCRIPT= $(TOPDIR)/$(CPUDIR)/u-boot-nand_spl.lds
+LDFLAGS := -T $(nandobj)u-boot-nand_spl.lds -Ttext $(CONFIG_SYS_TEXT_BASE_SPL) \
+		$(LDFLAGS) $(LDFLAGS_FINAL)
+AFLAGS	+= -DCONFIG_NAND_SPL
+CFLAGS	+= -DCONFIG_NAND_SPL
+
+SOBJS	= start.o resetvec.o
+COBJS	= cache.o cpu_init_early.o cpu_init_nand.o fsl_law.o law.o \
+	  nand_boot.o nand_boot_fsl_elbc.o ns16550.o tlb.o tlb_table.o
+
+SRCS	:= $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS))
+__OBJS	:= $(SOBJS) $(COBJS)
+LNDIR	:= $(nandobj)board/$(BOARDDIR)
+
+ALL	= $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin $(nandobj)u-boot-spl-16k.bin
+
+all:	$(obj).depend $(ALL)
+
+$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl
+	$(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@
+
+$(nandobj)u-boot-spl.bin:	$(nandobj)u-boot-spl
+	$(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
+
+$(nandobj)u-boot-spl:	$(OBJS) $(nandobj)u-boot-nand_spl.lds
+	cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) $(PLATFORM_LIBS) \
+		-Map $(nandobj)u-boot-spl.map \
+		-o $(nandobj)u-boot-spl
+
+$(nandobj)u-boot-nand_spl.lds: $(LDSCRIPT)
+	$(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@
+
+# create symbolic links for common files
+
+$(obj)cache.c:
+	@rm -f $(obj)cache.c
+	ln -sf $(SRCTREE)/arch/powerpc/lib/cache.c $(obj)cache.c
+
+$(obj)cpu_init_early.c:
+	@rm -f $(obj)cpu_init_early.c
+	ln -sf $(SRCTREE)/$(CPUDIR)/cpu_init_early.c $(obj)cpu_init_early.c
+
+$(obj)cpu_init_nand.c:
+	@rm -f $(obj)cpu_init_nand.c
+	ln -sf $(SRCTREE)/$(CPUDIR)/cpu_init_nand.c $(obj)cpu_init_nand.c
+
+$(obj)fsl_law.c:
+	@rm -f $(obj)fsl_law.c
+	ln -sf $(SRCTREE)/drivers/misc/fsl_law.c $(obj)fsl_law.c
+
+$(obj)law.c:
+	@rm -f $(obj)law.c
+	ln -sf $(SRCTREE)/board/$(BOARDDIR)/law.c $(obj)law.c
+
+$(obj)nand_boot_fsl_elbc.c:
+	@rm -f $(obj)nand_boot_fsl_elbc.c
+	ln -sf $(SRCTREE)/nand_spl/nand_boot_fsl_elbc.c \
+	       $(obj)nand_boot_fsl_elbc.c
+
+$(obj)ns16550.c:
+	@rm -f $(obj)ns16550.c
+	ln -sf $(SRCTREE)/drivers/serial/ns16550.c $(obj)ns16550.c
+
+$(obj)resetvec.S:
+	@rm -f $(obj)resetvec.S
+	ln -s $(SRCTREE)/$(CPUDIR)/resetvec.S $(obj)resetvec.S
+
+$(obj)fixed_ivor.S:
+	@rm -f $(obj)fixed_ivor.S
+	ln -sf $(SRCTREE)/$(CPUDIR)/fixed_ivor.S $(obj)fixed_ivor.S
+
+$(obj)start.S: $(obj)fixed_ivor.S
+	@rm -f $(obj)start.S
+	ln -sf $(SRCTREE)/$(CPUDIR)/start.S $(obj)start.S
+
+$(obj)tlb.c:
+	@rm -f $(obj)tlb.c
+	ln -sf $(SRCTREE)/$(CPUDIR)/tlb.c $(obj)tlb.c
+
+$(obj)tlb_table.c:
+	@rm -f $(obj)tlb_table.c
+	ln -sf $(SRCTREE)/board/$(BOARDDIR)/tlb.c $(obj)tlb_table.c
+
+ifneq ($(OBJTREE), $(SRCTREE))
+$(obj)nand_boot.c:
+	@rm -f $(obj)nand_boot.c
+	ln -s $(SRCTREE)/nand_spl/board/$(BOARDDIR)/nand_boot.c $(obj)nand_boot.c
+endif
+
+#########################################################################
+
+$(obj)%.o:	$(obj)%.S
+	$(CC) $(AFLAGS) -c -o $@ $<
+
+$(obj)%.o:	$(obj)%.c
+	$(CC) $(CFLAGS) -c -o $@ $<
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/nand_spl/board/freescale/p1023rds/nand_boot.c b/nand_spl/board/freescale/p1023rds/nand_boot.c
new file mode 100644
index 0000000000000000000000000000000000000000..0065c876dedfae63ed4eeeea989d5a7843d14f89
--- /dev/null
+++ b/nand_spl/board/freescale/p1023rds/nand_boot.c
@@ -0,0 +1,99 @@
+/*
+ * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * Author: Roy Zang <tie-fei.zang@freescale.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ *
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <asm/io.h>
+#include <nand.h>
+#include <asm/fsl_law.h>
+
+/* Fixed sdram init -- doesn't use serial presence detect. */
+void sdram_init(void)
+{
+	ccsr_ddr_t *ddr = (ccsr_ddr_t *)CONFIG_SYS_MPC85xx_DDR_ADDR;
+
+	set_next_law(0, LAW_SIZE_2G, LAW_TRGT_IF_DDR_1);
+
+	out_be32(&ddr->cs0_bnds, CONFIG_SYS_DDR_CS0_BNDS);
+	out_be32(&ddr->cs0_config, CONFIG_SYS_DDR_CS0_CONFIG);
+	out_be32(&ddr->cs1_bnds, CONFIG_SYS_DDR_CS1_BNDS);
+	out_be32(&ddr->cs1_config, CONFIG_SYS_DDR_CS1_CONFIG);
+	out_be32(&ddr->timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+	out_be32(&ddr->timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+	out_be32(&ddr->timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+	out_be32(&ddr->timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+	out_be32(&ddr->sdram_cfg_2, CONFIG_SYS_DDR_CONTROL2);
+	out_be32(&ddr->sdram_mode, CONFIG_SYS_DDR_MODE_1);
+	out_be32(&ddr->sdram_mode_2, CONFIG_SYS_DDR_MODE_2);
+	out_be32(&ddr->sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+	out_be32(&ddr->sdram_data_init, CONFIG_SYS_DDR_DATA_INIT);
+	out_be32(&ddr->sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CTRL);
+	out_be32(&ddr->timing_cfg_4, CONFIG_SYS_DDR_TIMING_4);
+	out_be32(&ddr->timing_cfg_5, CONFIG_SYS_DDR_TIMING_5);
+	out_be32(&ddr->ddr_zq_cntl, CONFIG_SYS_DDR_ZQ_CNTL);
+	out_be32(&ddr->ddr_wrlvl_cntl, CONFIG_SYS_DDR_WRLVL_CNTL);
+	out_be32(&ddr->ddr_cdr1, CONFIG_SYS_DDR_CDR_1);
+	out_be32(&ddr->ddr_cdr2, CONFIG_SYS_DDR_CDR_2);
+	out_be32(&ddr->sdram_cfg, CONFIG_SYS_DDR_CONTROL);
+}
+
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio, bus_clk;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+	/* initialize selected port with appropriate baud rate */
+	plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+	plat_ratio >>= 1;
+	bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+			bus_clk / 16 / CONFIG_BAUDRATE);
+
+	puts("\nNAND boot... ");
+	/* Initialize the DDR3 */
+	sdram_init();
+	/* copy code to RAM and jump to it - this should not return */
+	/* NOTE - code has to be copied out of NAND buffer before
+	 * other blocks can be read.
+	 */
+	relocate_code(CONFIG_SYS_NAND_U_BOOT_RELOC_SP, 0,
+			CONFIG_SYS_NAND_U_BOOT_RELOC);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	nand_boot();
+}
+
+void putc(char c)
+{
+	if (c == '\n')
+		NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
+
+	NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
+}
+
+void puts(const char *str)
+{
+	while (*str)
+		putc(*str++);
+}