diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
index 313f9f36a65cbfc5c61acd45f6b75287fdb73f88..3ffdac8bd5e679ac8228b0f10e7d874d62bed29e 100644
--- a/board/amcc/bamboo/bamboo.c
+++ b/board/amcc/bamboo/bamboo.c
@@ -521,67 +521,6 @@ int pci_pre_init(struct pci_controller *hose)
}
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Set up Direct MMIO registers
- *--------------------------------------------------------------------------*/
- /*--------------------------------------------------------------------------+
- | PowerPC440 EP PCI Master configuration.
- | Map one 1Gig range of PLB/processor addresses to PCI memory space.
- | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
- | Use byte reversed out routines to handle endianess.
- | Make this region non-prefetchable.
- +--------------------------------------------------------------------------*/
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*--------------------------------------------------------------------------+
- * Set up Configuration registers
- *--------------------------------------------------------------------------*/
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
/*************************************************************************
* pci_master_init
*
diff --git a/board/amcc/canyonlands/canyonlands.c b/board/amcc/canyonlands/canyonlands.c
index 9a8ca8eceab3b6d149bf9255b8a112528a9ae864..13a0daced774ae24ebeb579df73f0fb4633998f7 100644
--- a/board/amcc/canyonlands/canyonlands.c
+++ b/board/amcc/canyonlands/canyonlands.c
@@ -326,43 +326,6 @@ phys_size_t initdram(int board_type)
}
#endif
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*
- * Disable everything
- */
- out_le32((void *)PCIL0_PIM0SA, 0); /* disable */
- out_le32((void *)PCIL0_PIM1SA, 0); /* disable */
- out_le32((void *)PCIL0_PIM2SA, 0); /* disable */
- out_le32((void *)PCIL0_EROMBA, 0); /* disable expansion rom */
-
- /*
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
- * strapping options to not support sizes such as 128/256 MB.
- */
- out_le32((void *)PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out_le32((void *)PCIL0_PIM0LAH, 0);
- out_le32((void *)PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
- out_le32((void *)PCIL0_BAR0, 0);
-
- /*
- * Program the board's subsystem id/vendor id
- */
- out_le16((void *)PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out_le16((void *)PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
- out_le16((void *)PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
#if defined(CONFIG_PCI)
int board_pcie_first(void)
{
diff --git a/board/amcc/ebony/ebony.c b/board/amcc/ebony/ebony.c
index 1524b5333a4d6dd8863f024abf80e20a4d32db6c..e4d168f9d847cd7efc936e0752215fa4c86e1e8e 100644
--- a/board/amcc/ebony/ebony.c
+++ b/board/amcc/ebony/ebony.c
@@ -195,42 +195,3 @@ int pci_pre_init(struct pci_controller *hose)
return 1;
}
#endif /* defined(CONFIG_PCI) */
-
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r(PCIL0_PIM0SA, 0); /* disable */
- out32r(PCIL0_PIM1SA, 0); /* disable */
- out32r(PCIL0_PIM2SA, 0); /* disable */
- out32r(PCIL0_EROMBA, 0); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r(PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out32r(PCIL0_PIM0LAH, 0);
- out32r(PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
-
- out32r(PCIL0_BAR0, 0);
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r(PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out16r(PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
- out16r(PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c
index f43e76448bb9632258cadf0fbdab59ea2dcfde3b..f0b48c0d320975f9e9a1e0273d7948e01e8af793 100644
--- a/board/amcc/katmai/katmai.c
+++ b/board/amcc/katmai/katmai.c
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2007-2008
+ * (C) Copyright 2007-2009
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* See file CREDITS for list of people who contributed to this
@@ -291,44 +291,6 @@ int pci_pre_init(struct pci_controller * hose )
}
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*-------------------------------------------------------------------+
- * Disable everything
- *-------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*-------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
- * strapping options to not support sizes such as 128/256 MB.
- *-------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
- out32r( PCIL0_BAR0, 0 );
-
- /*-------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *-------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
#if defined(CONFIG_PCI)
int board_pcie_card_present(int port)
{
diff --git a/board/amcc/luan/luan.c b/board/amcc/luan/luan.c
index 94ba6437f6dbd4ca56ca7fc657fb2420e614a596..e0b297e7072af2a13ff6cf8d74a08dfa679f36a6 100644
--- a/board/amcc/luan/luan.c
+++ b/board/amcc/luan/luan.c
@@ -159,46 +159,6 @@ int pci_pre_init( struct pci_controller *hose )
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
- out32r( PCIL0_BAR0, 0 );
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-
/*************************************************************************
* hw_watchdog_reset
*
diff --git a/board/amcc/ocotea/ocotea.c b/board/amcc/ocotea/ocotea.c
index 2f64764ee2942911a11aafbf60531bae7256d5a2..b38f3cc400fdba9df8a20e22730eff3dca89dc78 100644
--- a/board/amcc/ocotea/ocotea.c
+++ b/board/amcc/ocotea/ocotea.c
@@ -307,46 +307,6 @@ int pci_pre_init(struct pci_controller * hose )
}
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
- out32r( PCIL0_BAR0, 0 );
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-
void fpga_init(void)
{
unsigned long group;
diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c
index 43938200616375db74c36e175bd5348963af398d..b8ef4e7633755cec9e11c6449ea6c522c3aff19f 100644
--- a/board/amcc/sequoia/sequoia.c
+++ b/board/amcc/sequoia/sequoia.c
@@ -427,71 +427,6 @@ int pci_pre_init(struct pci_controller *hose)
}
#endif /* defined(CONFIG_PCI) */
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*
- * Set up Direct MMIO registers
- */
- /*
- * PowerPC440EPX PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0xA0000000-0xDFFFFFFF
- * ==> PCI address 0xA0000000-0xDFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
void pci_master_init(struct pci_controller *hose)
{
diff --git a/board/amcc/taishan/taishan.c b/board/amcc/taishan/taishan.c
index 81e8fe14ab84346434aa06f089bab2bedc2ea3dd..574ff1a7bc20cc02d2e42ecc4b856ef17789a482 100644
--- a/board/amcc/taishan/taishan.c
+++ b/board/amcc/taishan/taishan.c
@@ -240,45 +240,6 @@ int pci_pre_init(struct pci_controller * hose )
}
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
- out32r( PCIL0_BAR0, 0 );
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
#ifdef CONFIG_POST
/*
* Returns 1 if keys pressed to start the power-on long-running tests
diff --git a/board/amcc/yosemite/yosemite.c b/board/amcc/yosemite/yosemite.c
index e416eeb1676c47a0e5f0aad919120bd7e50b82ec..cd14a6a487ddd7e6fc306beb19fb8179a6307806 100644
--- a/board/amcc/yosemite/yosemite.c
+++ b/board/amcc/yosemite/yosemite.c
@@ -407,67 +407,6 @@ int pci_pre_init(struct pci_controller *hose)
}
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Set up Direct MMIO registers
- *--------------------------------------------------------------------------*/
- /*--------------------------------------------------------------------------+
- | PowerPC440 EP PCI Master configuration.
- | Map one 1Gig range of PLB/processor addresses to PCI memory space.
- | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
- | Use byte reversed out routines to handle endianess.
- | Make this region non-prefetchable.
- +--------------------------------------------------------------------------*/
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*--------------------------------------------------------------------------+
- * Set up Configuration registers
- *--------------------------------------------------------------------------*/
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
/*************************************************************************
* pci_master_init
*
diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c
index 7315033dc89abd2f69a9a97c96b63f7866d7b8a0..0ec26f14d19e01186af45e0e5dfffd488ec880a0 100644
--- a/board/amcc/yucca/yucca.c
+++ b/board/amcc/yucca/yucca.c
@@ -619,44 +619,6 @@ int pci_pre_init(struct pci_controller * hose )
}
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*-------------------------------------------------------------------+
- * Disable everything
- *-------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*-------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
- * strapping options to not support sizes such as 128/256 MB.
- *-------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
- out32r( PCIL0_BAR0, 0 );
-
- /*-------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *-------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
#if defined(CONFIG_PCI)
int board_pcie_card_present(int port)
{
diff --git a/board/esd/du440/du440.c b/board/esd/du440/du440.c
index 8f9f9500e298af849429f56939f9ccbb035807c4..866dcafcfa37aa7cbcac24c3e349c056b5f23a63 100644
--- a/board/esd/du440/du440.c
+++ b/board/esd/du440/du440.c
@@ -414,73 +414,6 @@ int pci_pre_init(struct pci_controller *hose)
}
#endif /* defined(CONFIG_PCI) */
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*
- * Set up Direct MMIO registers
- */
- /*
- * PowerPC440EPX PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0xA0000000-0xDFFFFFFF
- * ==> PCI address 0xA0000000-0xDFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- PCI_VENDOR_ID_ESDGMBH);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, PCI_DEVICE_ID_DU440);
-
- pci_write_config_word(0, PCI_CLASS_SUB_CODE, PCI_CLASS_BRIDGE_HOST);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
void pci_master_init(struct pci_controller *hose)
{
diff --git a/board/esd/du440/du440.h b/board/esd/du440/du440.h
index a124a7ee9b51df8f16f245a55247673efbb87b4d..37697ec854f985a4cd44d95abe0b387322fa1d59 100644
--- a/board/esd/du440/du440.h
+++ b/board/esd/du440/du440.h
@@ -38,6 +38,3 @@
#define PWR_RDY 0x10
#define CPLD_IRQ (32+30)
-
-#define PCI_VENDOR_ID_ESDGMBH 0x12fe
-#define PCI_DEVICE_ID_DU440 0x0444
diff --git a/board/gdsys/gdppc440etx/gdppc440etx.c b/board/gdsys/gdppc440etx/gdppc440etx.c
index 92f5d822f69ce8d87d1538b093b252a6f32611b4..b93a420154f6d379d587dc337363f8b7c6e250ba 100644
--- a/board/gdsys/gdppc440etx/gdppc440etx.c
+++ b/board/gdsys/gdppc440etx/gdppc440etx.c
@@ -216,69 +216,6 @@ int pci_pre_init(struct pci_controller *hose)
}
#endif /* defined(CONFIG_PCI) */
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*
- * Set up Direct MMIO registers
- */
-
- /*
- * PowerPC440 EP PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0xA0000000-0xDFFFFFFF
- * ==> PCI address 0xA0000000-0xDFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- out32r(PCIL0_PMM0MA, 0x00000000); /* disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
- out32r(PCIL0_PMM0PCIHA, 0x00000000);
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M, no prefetch, enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2);
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
- out32r(PCIL0_PMM1PCIHA, 0x00000000);
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M, no prefetch, enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001);
- out32r(PCIL0_PTM1LA, 0);
- out32r(PCIL0_PTM2MS, 0);
- out32r(PCIL0_PTM2LA, 0);
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
/*
* pci_master_init
*
diff --git a/board/gdsys/intip/intip.c b/board/gdsys/intip/intip.c
index 49d245135821c2bd05b7da38bedeeb0259fd85cc..23a10c41f9f415c0c082d8fda0686edc23684163 100644
--- a/board/gdsys/intip/intip.c
+++ b/board/gdsys/intip/intip.c
@@ -141,43 +141,6 @@ int checkboard(void)
return 0;
}
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*
- * Disable everything
- */
- out_le32((void *)PCIL0_PIM0SA, 0); /* disable */
- out_le32((void *)PCIL0_PIM1SA, 0); /* disable */
- out_le32((void *)PCIL0_PIM2SA, 0); /* disable */
- out_le32((void *)PCIL0_EROMBA, 0); /* disable expansion rom */
-
- /*
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
- * strapping options to not support sizes such as 128/256 MB.
- */
- out_le32((void *)PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out_le32((void *)PCIL0_PIM0LAH, 0);
- out_le32((void *)PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
- out_le32((void *)PCIL0_BAR0, 0);
-
- /*
- * Program the board's subsystem id/vendor id
- */
- out_le16((void *)PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out_le16((void *)PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
- out_le16((void *)PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
int board_early_init_r(void)
{
/*
diff --git a/board/korat/korat.c b/board/korat/korat.c
index b0e6a56a63c0bf5cf8f755184e3b98df97ff40e1..02ebfdf37107f5e1000f35479aaf6cfc7edbaf25 100644
--- a/board/korat/korat.c
+++ b/board/korat/korat.c
@@ -35,6 +35,7 @@
#include <asm/io.h>
#include <asm/ppc4xx-uic.h>
#include <asm/processor.h>
+#include <asm/4xx_pci.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -668,60 +669,8 @@ int pci_pre_init(struct pci_controller *hose)
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
void pci_target_init(struct pci_controller *hose)
{
- /*
- * Set up Direct MMIO registers
- */
- /*
- * PowerPC440EPX PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0x80000000-0xBFFFFFFF
- * ==> PCI address 0x80000000-0xBFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA,
- CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM1LA,
- CONFIG_SYS_PCI_MEMBASE + 0x20000000); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA,
- CONFIG_SYS_PCI_MEMBASE + 0x20000000); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
+ /* First do 440EP(x) common setup */
+ __pci_target_init(hose);
/*
* Set up Configuration registers for on-board NEC uPD720101 USB
diff --git a/board/lwmon5/lwmon5.c b/board/lwmon5/lwmon5.c
index 09ba2b933d64571d492f757a291ab19132655ea2..77f2d7f688fb6f8059058086da914c5a7afe3bc8 100644
--- a/board/lwmon5/lwmon5.c
+++ b/board/lwmon5/lwmon5.c
@@ -330,67 +330,6 @@ int pci_pre_init(struct pci_controller *hose)
}
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Set up Direct MMIO registers
- *--------------------------------------------------------------------------*/
- /*--------------------------------------------------------------------------+
- | PowerPC440EPX PCI Master configuration.
- | Map one 1Gig range of PLB/processor addresses to PCI memory space.
- | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
- | Use byte reversed out routines to handle endianess.
- | Make this region non-prefetchable.
- +--------------------------------------------------------------------------*/
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*--------------------------------------------------------------------------+
- * Set up Configuration registers
- *--------------------------------------------------------------------------*/
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
/*************************************************************************
* pci_master_init
*
diff --git a/board/netstal/hcu5/hcu5.c b/board/netstal/hcu5/hcu5.c
index 7ffc2620245758f70640bf26873d35f21f6fe011..144fdd97047f0120eb05cbb312349a014d6a18d3 100644
--- a/board/netstal/hcu5/hcu5.c
+++ b/board/netstal/hcu5/hcu5.c
@@ -376,71 +376,6 @@ int pci_pre_init(struct pci_controller *hose)
return board_with_pci();
}
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- */
-void pci_target_init(struct pci_controller *hose)
-{
- if (!board_with_pci()) { return; }
- /*
- * Set up Direct MMIO registers
- *
- * PowerPC440EPX PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0xA0000000-0xDFFFFFFF ==> PCI address
- * 0xA0000000-0xDFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM0MA, 0x00000000);
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- /* 512M + No prefetching, and enable region */
- out32r(PCIL0_PMM0MA, 0xE0000001);
-
- /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM1MA, 0x00000000);
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- /* 512M + No prefetching, and enable region */
- out32r(PCIL0_PMM1MA, 0xE0000001);
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-}
-
/*
* pci_master_init
*
diff --git a/board/pcs440ep/pcs440ep.c b/board/pcs440ep/pcs440ep.c
index 2155711d6f839c9f6bfb3f2a05f10d251b5cb378..929375987cc8808d07e59c05a9460cc9bb464128 100644
--- a/board/pcs440ep/pcs440ep.c
+++ b/board/pcs440ep/pcs440ep.c
@@ -605,67 +605,6 @@ int pci_pre_init(struct pci_controller *hose)
}
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Set up Direct MMIO registers
- *--------------------------------------------------------------------------*/
- /*--------------------------------------------------------------------------+
- | PowerPC440 EP PCI Master configuration.
- | Map one 1Gig range of PLB/processor addresses to PCI memory space.
- | PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
- | Use byte reversed out routines to handle endianess.
- | Make this region non-prefetchable.
- +--------------------------------------------------------------------------*/
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute - disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*--------------------------------------------------------------------------+
- * Set up Configuration registers
- *--------------------------------------------------------------------------*/
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
/*************************************************************************
* pci_master_init
*
diff --git a/board/prodrive/alpr/alpr.c b/board/prodrive/alpr/alpr.c
index e9e2bf3e0ba2e1311c16c424355d201a2173702a..c06aadb4141beb2181323cd2f0d2a217c06c04bd 100644
--- a/board/prodrive/alpr/alpr.c
+++ b/board/prodrive/alpr/alpr.c
@@ -178,45 +178,6 @@ int pci_pre_init(struct pci_controller * hose )
}
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
- out32r( PCIL0_BAR0, 0 );
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
/*************************************************************************
* Override weak is_pci_host()
*
diff --git a/board/prodrive/p3p440/p3p440.c b/board/prodrive/p3p440/p3p440.c
index e07400794b063f2a9604e70fcc528cfe04269f69..5761e708454b961304503a2d9606d4635cb26383 100644
--- a/board/prodrive/p3p440/p3p440.c
+++ b/board/prodrive/p3p440/p3p440.c
@@ -195,45 +195,6 @@ int pci_pre_init(struct pci_controller *hose)
}
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r(PCIL0_PIM0SA, 0); /* disable */
- out32r(PCIL0_PIM1SA, 0); /* disable */
- out32r(PCIL0_PIM2SA, 0); /* disable */
- out32r(PCIL0_EROMBA, 0); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r(PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out32r(PCIL0_PIM0LAH, 0);
- out32r(PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
-
- out32r(PCIL0_BAR0, 0);
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r(PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out16r(PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
- out16r(PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
/*************************************************************************
* Override weak is_pci_host()
*
diff --git a/board/sandburst/common/sb_common.c b/board/sandburst/common/sb_common.c
index 5749084583c4a56556682cca0a1b07a1835376f0..45e9043851ec510b7dc8cbfc018eb4bf8e09b602 100644
--- a/board/sandburst/common/sb_common.c
+++ b/board/sandburst/common/sb_common.c
@@ -332,46 +332,6 @@ int pci_pre_init(struct pci_controller * hose )
}
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*--------------------------------------------------------------------------+
- * Disable everything
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0SA, 0 ); /* disable */
- out32r( PCIL0_PIM1SA, 0 ); /* disable */
- out32r( PCIL0_PIM2SA, 0 ); /* disable */
- out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
- /*--------------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- *--------------------------------------------------------------------------*/
- out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
- out32r( PCIL0_PIM0LAH, 0 );
- out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
- out32r( PCIL0_BAR0, 0 );
-
- /*--------------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *--------------------------------------------------------------------------*/
- out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
- out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-
/*************************************************************************
* board_get_enetaddr
*
diff --git a/board/xes/xpedite1000/xpedite1000.c b/board/xes/xpedite1000/xpedite1000.c
index 0c4cf9463fafd5f08237021c49774ab7220f26ef..db37ca0516ab0b7342719921fcf4c9e1438ca4a9 100644
--- a/board/xes/xpedite1000/xpedite1000.c
+++ b/board/xes/xpedite1000/xpedite1000.c
@@ -166,38 +166,6 @@ int pci_pre_init(struct pci_controller * hose)
}
#endif /* defined(CONFIG_PCI) */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-/*
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-void pci_target_init(struct pci_controller * hose)
-{
- /* Disable everything */
- out32r(PCIL0_PIM0SA, 0);
- out32r(PCIL0_PIM1SA, 0);
- out32r(PCIL0_PIM2SA, 0);
- out32r(PCIL0_EROMBA, 0); /* disable expansion rom */
-
- /*
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
- * options to not support sizes such as 128/256 MB.
- */
- out32r(PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
- out32r(PCIL0_PIM0LAH, 0);
- out32r(PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
-
- out32r(PCIL0_BAR0, 0);
-
- /* Program the board's subsystem id/vendor id */
- out16r(PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
- out16r(PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
- out16r(PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
#if defined(CONFIG_PCI)
/*
* Override weak is_pci_host()
diff --git a/cpu/ppc4xx/4xx_pci.c b/cpu/ppc4xx/4xx_pci.c
index 40017f4d6b57b1495ef3d001d3b65e23b09cd75f..20e134b63e9ddb9cf3033eaa9675fd2cd398f16f 100644
--- a/cpu/ppc4xx/4xx_pci.c
+++ b/cpu/ppc4xx/4xx_pci.c
@@ -77,6 +77,7 @@
#include <asm/4xx_pci.h>
#endif
#include <asm/processor.h>
+#include <asm/io.h>
#include <pci.h>
#ifdef CONFIG_PCI
@@ -499,6 +500,111 @@ int __is_pci_host(struct pci_controller *hose)
int is_pci_host(struct pci_controller *hose)
__attribute__((weak, alias("__is_pci_host")));
+/*
+ * pci_target_init
+ *
+ * The bootstrap configuration provides default settings for the pci
+ * inbound map (PIM). But the bootstrap config choices are limited and
+ * may not be sufficient for a given board.
+ */
+#if defined(CONFIG_SYS_PCI_TARGET_INIT)
+#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
+ defined(CONFIG_440GR) || defined(CONFIG_440GRX)
+void __pci_target_init(struct pci_controller *hose)
+{
+ /*
+ * Set up Direct MMIO registers
+ */
+
+ /*
+ * PowerPC440 EP PCI Master configuration.
+ * Map one 1Gig range of PLB/processor addresses to PCI memory space.
+ * PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
+ * Use byte reversed out routines to handle endianess.
+ * Make this region non-prefetchable.
+ */
+ /* PMM0 Mask/Attribute - disabled b4 setting */
+ out_le32((void *)PCIL0_PMM0MA, 0x00000000);
+ /* PMM0 Local Address */
+ out_le32((void *)PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);
+ /* PMM0 PCI Low Address */
+ out_le32((void *)PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
+ /* PMM0 PCI High Address */
+ out_le32((void *)PCIL0_PMM0PCIHA, 0x00000000);
+ /* 512M + No prefetching, and enable region */
+ out_le32((void *)PCIL0_PMM0MA, 0xE0000001);
+
+ /* PMM1 Mask/Attribute - disabled b4 setting */
+ out_le32((void *)PCIL0_PMM1MA, 0x00000000);
+ /* PMM1 Local Address */
+ out_le32((void *)PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2);
+ /* PMM1 PCI Low Address */
+ out_le32((void *)PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
+ /* PMM1 PCI High Address */
+ out_le32((void *)PCIL0_PMM1PCIHA, 0x00000000);
+ /* 512M + No prefetching, and enable region */
+ out_le32((void *)PCIL0_PMM1MA, 0xE0000001);
+
+ out_le32((void *)PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
+ out_le32((void *)PCIL0_PTM1LA, 0); /* Local Addr. Reg */
+ out_le32((void *)PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
+ out_le32((void *)PCIL0_PTM2LA, 0); /* Local Addr. Reg */
+
+ /*
+ * Set up Configuration registers
+ */
+
+ /* Program the board's subsystem id/vendor id */
+ pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
+ CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
+
+ /* Configure command register as bus master */
+ pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
+
+ /* 240nS PCI clock */
+ pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
+
+ /* No error reporting */
+ pci_write_config_word(0, PCI_ERREN, 0);
+
+ pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
+}
+#else /* defined(CONFIG_440EP) ... */
+void __pci_target_init(struct pci_controller * hose)
+{
+ /*
+ * Disable everything
+ */
+ out_le32((void *)PCIL0_PIM0SA, 0); /* disable */
+ out_le32((void *)PCIL0_PIM1SA, 0); /* disable */
+ out_le32((void *)PCIL0_PIM2SA, 0); /* disable */
+ out_le32((void *)PCIL0_EROMBA, 0); /* disable expansion rom */
+
+ /*
+ * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
+ * strapping options do not support sizes such as 128/256 MB.
+ */
+ out_le32((void *)PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
+ out_le32((void *)PCIL0_PIM0LAH, 0);
+ out_le32((void *)PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
+ out_le32((void *)PCIL0_BAR0, 0);
+
+ /*
+ * Program the board's subsystem id/vendor id
+ */
+ out_le16((void *)PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ out_le16((void *)PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
+
+ out_le16((void *)PCIL0_CMD, in_le16((void *)PCIL0_CMD) |
+ PCI_COMMAND_MEMORY);
+}
+#endif /* defined(CONFIG_440EP) ... */
+void pci_target_init(struct pci_controller * hose)
+ __attribute__((weak, alias("__pci_target_init")));
+
+#endif /* defined(CONFIG_SYS_PCI_TARGET_INIT) */
+
int pci_440_init (struct pci_controller *hose)
{
int reg_num = 0;
diff --git a/include/asm-ppc/4xx_pci.h b/include/asm-ppc/4xx_pci.h
index 30125a19ef65629946c8967dac6f2d7ceb8de894..5400a035ea0da274e36d8a996790d3202f1f9555 100644
--- a/include/asm-ppc/4xx_pci.h
+++ b/include/asm-ppc/4xx_pci.h
@@ -49,4 +49,6 @@
#define PCIDEVID_405GP 0x0
+void __pci_target_init(struct pci_controller *hose);
+
#endif
diff --git a/include/configs/DU440.h b/include/configs/DU440.h
index e9ea1bf7d0878072dc3cad39ccd04ac936f02929..65dc2359d01b0a01405c647630a8a3ab58473a6b 100644
--- a/include/configs/DU440.h
+++ b/include/configs/DU440.h
@@ -60,8 +60,9 @@
#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
-#define CONFIG_SYS_PCI_IOBASE 0xe8000000
-
+#define CONFIG_SYS_PCI_IOBASE 0xe8000000
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID PCI_VENDOR_ID_ESDGMBH
+#define CONFIG_SYS_PCI_SUBSYS_ID 0x0444 /* device ID for DU440 */
/* Don't change either of these */
#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */
diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h
index d6e2f6bc5e2be03e4610e676ca11264a9744f3e3..d2c5188a67203ffb73e7bf221d5375ef6938f815 100644
--- a/include/configs/PMC440.h
+++ b/include/configs/PMC440.h
@@ -440,6 +440,8 @@
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CONFIG_SYS_PCI_SUBSYS_ID_NONMONARCH 0x0441 /* PCI Device ID: Non-Monarch */
#define CONFIG_SYS_PCI_SUBSYS_ID_MONARCH 0x0440 /* PCI Device ID: Monarch */
+/* for weak __pci_target_init() */
+#define CONFIG_SYS_PCI_SUBSYS_ID CONFIG_SYS_PCI_SUBSYS_ID_MONARCH
#define CONFIG_SYS_PCI_CLASSCODE_NONMONARCH PCI_CLASS_PROCESSOR_POWERPC
#define CONFIG_SYS_PCI_CLASSCODE_MONARCH PCI_CLASS_BRIDGE_HOST
diff --git a/include/configs/korat.h b/include/configs/korat.h
index ea6ba8938d7b6463e1408b206dd900a3c4c8e0b1..7e74ef7051419782da8231a35484a10259f6e7be 100644
--- a/include/configs/korat.h
+++ b/include/configs/korat.h
@@ -69,6 +69,7 @@
#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE
#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
+#define CONFIG_SYS_PCI_MEMBASE2 (CONFIG_SYS_PCI_MEMBASE + 0x20000000)
/* Don't change either of these */
#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */